Search found 20 matches

by turtleman
Thu Jan 03, 2019 8:10 pm
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

Thank you, I will print with bed heated all the way and reset the others. I do not have an enclosure for I but will pre-heat bed then print. I have Simplify3D and need to adjust some settings then. Any other hints would be great, Thanks
by turtleman
Thu Jan 03, 2019 5:25 pm
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

I am making parts and would like to know How many layers I should have my bed temp @ 80c, my hot end is at 255 and a slower prints speed. The part is tall and about 1/8 inch thick. I get worping and the part break in layers easy. Any help please.
by turtleman
Sun Dec 02, 2018 2:53 am
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

I have a part that I want to make and its just over 1/8 thick walls that make it up. Here is a pic not sure you can see what's going.
by turtleman
Sun Dec 02, 2018 2:47 am
Forum: Tech Support
Topic: Feed motor
Replies: 2
Views: 342

Re: Feed motor

Thanks, I forgot about that, its working fine now
by turtleman
Sat Dec 01, 2018 1:56 am
Forum: Tech Support
Topic: Feed motor
Replies: 2
Views: 342

Feed motor

I was changing filament and when I tried to start it, it would not feed. I found a piece of the old filament and then tried it again. The motor would not run. Is their a fuse somewhere that I need to change?

Thanks
by turtleman
Fri Nov 30, 2018 4:30 pm
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

I am making a part that I need strength, flexibility and has weather resistance. I will send a picture of what I did last night but it started to warp so I stopped it.
sample2.jpg
sample2.jpg
I hope you can see them, and not the best at it.
by turtleman
Fri Nov 30, 2018 1:03 am
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

oh yes I also put a raft on this one
by turtleman
Fri Nov 30, 2018 1:01 am
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

Yes electric stove and using Simplify 3D slow print rate but not sure of layer height its printing now and very slow rate. Not sure what setting I have but still trying. When I get some layers I will snap a picture, and send it. I did the 5 hours today in the oven but think I forgot to reset temp, n...
by turtleman
Wed Nov 28, 2018 1:07 pm
Forum: Filament
Topic: side skirt
Replies: 2
Views: 338

side skirt

I want to put on a side-skirt to help hold down my part when printing. How do I do that? I have a M2
by turtleman
Tue Nov 27, 2018 11:51 pm
Forum: Filament
Topic: Nylon
Replies: 25
Views: 1785

Re: Nylon

Thank you so much, I did try again today to print, I put the roll in the oven for 4 hours at 170 degrees. I could not get it to stick on the corners.. The part is about 1/8 inch or more wide and it wants to worp on the corners. I know I was not going to sell it but just need to get it right so I can...