Sorry to hear such bad news.
Thanks to all the MakerGear Team for their support, and the very good products they design.
Could I do something to help you ?
Sincerely Yours
Search found 9 matches
- Thu Jun 23, 2022 5:50 pm
- Forum: General Discussion
- Topic: MakerGear Forum Shutting Down
- Replies: 11
- Views: 49495
- Wed Dec 29, 2021 6:35 pm
- Forum: M3-ID
- Topic: cold extruders don't have the same temperature
- Replies: 0
- Views: 70595
cold extruders don't have the same temperature
Hello,
I'm very happy with my M3 ID.
Recently I noticed that when T0 and T1 are "cold", the temperature displayed are clearly different (about 5 degrees).
Is it a way to adjust them ?
Thanks for your help
I'm very happy with my M3 ID.
Recently I noticed that when T0 and T1 are "cold", the temperature displayed are clearly different (about 5 degrees).
Is it a way to adjust them ?
Thanks for your help
- Sat Aug 14, 2021 5:34 pm
- Forum: Software
- Topic: M3 ID: Octoprint slicer dead after software upgrade
- Replies: 1
- Views: 12668
M3 ID: Octoprint slicer dead after software upgrade
Hi, I recently updated my octoprint plugins. I know, it was a bad idea :-). Previously, I was a happy user of the octoprint curaEngine slicer. I prefer it to S3D for very simple objects, and for objects that require a raft. S3D tends to produce rafts difficult (nearly impossible) to remove. But it s...
- Fri Nov 29, 2019 2:10 am
- Forum: Software
- Topic: Cura 2.3.0 MakerGear M2 file
- Replies: 18
- Views: 59656
Re: Cura 2.3.0 MakerGear M2 file
would love a config for Cura 4.3 I also think it's kind of hard that Utimaker doesn't provide the M2 in a preset. Hi, Thanks for your job. I will be greatly interested by a Cura profile for my Makergear M3 ID. I'm using the Cura slicer included in Octoprint as much as possible, but it is clearly le...
- Wed Jul 31, 2019 2:08 pm
- Forum: Tech Support
- Topic: X and Y timing belt tension
- Replies: 3
- Views: 6207
Re: X and Y timing belt tension
Hello,
thanks for your answer.
Actually, I was looking for a way to move the motor (and adjust the belt tension) with the right strength.
Some 3D printers use an adjustment screw, other use a spring to have the right tension.
Thanks for your help.
thanks for your answer.
Actually, I was looking for a way to move the motor (and adjust the belt tension) with the right strength.
Some 3D printers use an adjustment screw, other use a spring to have the right tension.
Thanks for your help.
- Tue Jul 30, 2019 10:48 am
- Forum: Tech Support
- Topic: X and Y timing belt tension
- Replies: 3
- Views: 6207
X and Y timing belt tension
Hello,
I'm the happy owner of a M3ID. Recently, the right X pulley begun to make noise when moving.
As the noise disappeard when I push on the belt, I think that should be more stretched.
Could you please explain how doing that.
Thanks
Best regards
I'm the happy owner of a M3ID. Recently, the right X pulley begun to make noise when moving.
As the noise disappeard when I push on the belt, I think that should be more stretched.
Could you please explain how doing that.
Thanks
Best regards
- Tue May 28, 2019 7:50 am
- Forum: M3-ID
- Topic: BL touch upgrade for M3ID
- Replies: 4
- Views: 10522
Re: BL touch upgrade for M3ID
Hi I installed my BL touch upgrade yesterday. Everything was fine, until I saw the hotend trying to print at 10cm above the bed. I stopped it, and saw this error message: "Recv: error detected bl touch set_bltouch_deployed1 Recv: Error: [002]-[11] Probe Deployment Error: Please restart your printer....
- Mon Feb 04, 2019 10:32 pm
- Forum: Tech Support
- Topic: M3 Dual Extruder doesn't boot anymore
- Replies: 2
- Views: 4700
Re: M3 Dual Extruder doesn't boot anymore
Hello,
thanks for your suggestion.
They answer with a piece of adive that solves the problem
Best regards
thanks for your suggestion.
They answer with a piece of adive that solves the problem
Best regards
- Sun Feb 03, 2019 7:14 pm
- Forum: Tech Support
- Topic: M3 Dual Extruder doesn't boot anymore
- Replies: 2
- Views: 4700
M3 Dual Extruder doesn't boot anymore
Hello, I was printing some mode, but things were going wrong... I decided to check the bed level, and reset the main M3 board. After that, the symptoms are: - at boot, the M3 emits only two notes instead of the whole boot set of notes. - the green led lights on, - the fan does not start, - the Octop...