Search found 10 matches
- Thu Aug 14, 2014 2:59 pm
- Forum: Tech Support
- Topic: Printer has a mind of its own!
- Replies: 3
- Views: 5502
Re: Printer has a mind of its own!
I FORGOT TO INCLUDE A MAJOR DETAIL: THE MACHINE WAS ACCIDENTALLY TURNED OFF DURING A PRINT, THEN PROMPTLY TURNED BACK ON.
- Tue Aug 12, 2014 8:04 pm
- Forum: Tech Support
- Topic: Printer has a mind of its own!
- Replies: 3
- Views: 5502
Printer has a mind of its own!
Printer has been working fine for a few weeks, but we went to print a job today and the extruder kept printing RIGHT ON TOP of the glass and making it tilt, and at one point, the glass dropped 2" suddenly and moved to the rear of the machine. I tried to recalibrate, but it seems as the machine has a...
- Wed Jul 16, 2014 4:42 pm
- Forum: Tech Support
- Topic: Clogged filament
- Replies: 11
- Views: 19561
Re: Clogged filament
Dale,
Here is a picture of where the clog is: at the top of the threaded screw is where it is most visible. Thanks a lot for your time.
Here is a picture of where the clog is: at the top of the threaded screw is where it is most visible. Thanks a lot for your time.
- Tue Jul 15, 2014 4:21 pm
- Forum: Tech Support
- Topic: Clogged filament
- Replies: 11
- Views: 19561
- Tue Jul 15, 2014 4:20 pm
- Forum: Tech Support
- Topic: Clogged filament
- Replies: 11
- Views: 19561
Clogged filament
There is a mixture of ABS and PLA clogged somewhere in the Bottom Filament Path (possibly below that). I tried to push it through with a piece of PLA and with an Alan wrench. It won't budge. I don't see a solution. Thanks a lot.
- Fri Jul 11, 2014 5:00 pm
- Forum: Tech Support
- Topic: Bed releveling
- Replies: 1
- Views: 3755
Bed releveling
When I print, It seems that the left side of the bed is too high, because it makes contact with the extruder and prevents the PLA from coming out. Do you have any releveling instructions?
Thanks
Thanks
- Fri Jul 11, 2014 4:15 pm
- Forum: Tech Support
- Topic: Printer can't connect to computer (simplify3D)
- Replies: 10
- Views: 20482
Re: Printer can't connect to computer (simplify3D)
I have a Mac/M2/S3d combo, but I sometimes have trouble if things are turned on, connected in the wrong order, or software started at the wrong time. Turn off the printer, exit s3D, unplug the printer USB. Plug in the USB, turn on the printer (give it a few seconds), then start S3D. It should conne...
- Fri Jul 11, 2014 4:14 pm
- Forum: Tech Support
- Topic: Printer can't connect to computer (simplify3D)
- Replies: 10
- Views: 20482
Re: Printer can't connect to computer (simplify3D)
Alright guys, I have tried all the steps, and here is a photo with the port recognized....
- Fri Jul 11, 2014 3:33 pm
- Forum: Tech Support
- Topic: Printer can't connect to computer (simplify3D)
- Replies: 10
- Views: 20482
Printer can't connect to computer (simplify3D)
Hey everyone,
Yesterday I printed from an SD Card for the first time. Today, when I attempt to connect to the computer via USB, the program reads, (see attachment). Any help would be greatly appreciated. Thanks.
Yesterday I printed from an SD Card for the first time. Today, when I attempt to connect to the computer via USB, the program reads, (see attachment). Any help would be greatly appreciated. Thanks.
- Wed Jul 09, 2014 4:40 pm
- Forum: Tech Support
- Topic: Large items do NOT print correctly.
- Replies: 2
- Views: 4651
Large items do NOT print correctly.
Hello, When I attempt to print an item in particular, about 8" x 4" on the glass, the PLA begins to print properly, but then it messes itself up and all the PLA gets tangled. It messes up the entire first layer. What is the cause of this? It is very frustrating. Any help is greatly appreciated. Than...