Does this help?
viewtopic.php?f=10&t=6647&p=37794#p37794
Search found 2012 matches
- Thu Dec 06, 2018 2:59 am
- Forum: General Discussion
- Topic: Bed Heater Wire Clamp Model
- Replies: 1
- Views: 661
- Thu Dec 06, 2018 2:50 am
- Forum: Modifications
- Topic: Pre-Rev. E HBP Wire Bracket Upgrade
- Replies: 2
- Views: 696
Re: Pre-Rev. E HBP Wire Bracket Upgrade
I stuck a Keenovo 250W/24v heater directly to the underside of a MIC6 plate, and I'm using your bracket to strain-relief the corregated tubing. Hopefully it goes well 

- Thu Dec 06, 2018 2:37 am
- Forum: Modifications
- Topic: Mic 6 tooling plate
- Replies: 212
- Views: 43621
Re: Mic 6 tooling plate
I found a handful of 7.75 x 10" MIC6 plates, about 4 left. mic6 [at] pingring.org if you want one.
- Thu Dec 06, 2018 2:36 am
- Forum: Modifications
- Topic: Runout sensor
- Replies: 8
- Views: 2610
Re: Runout sensor
I used the Y max endstop and mapped that in the firmware.
- Mon Jun 11, 2018 3:06 pm
- Forum: Filament
- Topic: Large Overhead Filament Spools
- Replies: 2
- Views: 646
Re: Large Overhead Filament Spools
I added filament runout sensors to my printers, now I just let them run until the 1kg spool runs out. The print pauses and waits for me to change out the filament, and everything works as I'd hope. With a simple print and a drill, you can also reload the 1kg spools from a 25kg master spool, too. Thi...
- Mon Jun 11, 2018 2:22 pm
- Forum: Getting Started
- Topic: (used) new makergear purchase
- Replies: 3
- Views: 1505
Re: (used) new makergear purchase
If it's a dual V4 extruder (vs a custom one) with a 3-point spider and a top-homing setup, it's a prototype dual -- so Rev D, ~ ish. I'd take the whole thing (carefully) apart, clean all the slides with WD40 / QTips over and over, and re-lube with sewing machine oil. Make sure the fans are clean and...
- Mon Jun 04, 2018 2:40 pm
- Forum: Tech Support
- Topic: Unexpected y-axis shift mid print
- Replies: 13
- Views: 3716
Re: Unexpected y-axis shift mid print
This is absolutely a weight/acceleration related issue, and if you haven't added a heavy aluminum bed, the default values of 3k for M201, M202 and M204 work perfectly fine for a part weight up to about 45grams. This is consistent across many different parts. Dropping those values to 2k (from 3k) al...
- Sun May 20, 2018 4:20 pm
- Forum: Tech Support
- Topic: Issues with the X-axis
- Replies: 8
- Views: 1642
Re: Issues with the X-axis
You can stop using that horrible lithium grease in the carriages. It's supposed to be a very thin machine oil. The lithium was for the old metal-on-metal Z axis. Take the carriage off, clean it out with WD40 and alcohol until it's dry, then lubricate with 1 drop per side of sewing machine oil. Clean...
- Fri May 18, 2018 3:45 pm
- Forum: Tech Support
- Topic: Layer Shifting on M3 ID
- Replies: 2
- Views: 756
Re: Layer Shifting on M3 ID
That's definitely nozzle drag. Z-Hop / Vertical lift will fix it. You only need 0.20mm
- Tue May 15, 2018 2:43 pm
- Forum: Tech Support
- Topic: Curling off of Raft
- Replies: 1
- Views: 394
Re: Curling off of Raft
Cooler bed, no raft. 
