Search found 30 matches
- Tue Mar 31, 2020 9:41 pm
- Forum: General Discussion
- Topic: 3D Printed CoronaVirus Respirators
- Replies: 18
- Views: 27982
Re: 3D Printed CoronaVirus Respirators
John, for now I just cut a strip of kitchen towel and attach it inside the mask with double sided tape. What I want to do is have a formed fit rubber insert that will give a good seal. Now if I put my hand over the front opening and try to breath, it is quite forced so the seal is really pretty good...
- Tue Mar 31, 2020 2:12 am
- Forum: General Discussion
- Topic: 3D Printed CoronaVirus Respirators
- Replies: 18
- Views: 27982
Re: 3D Printed CoronaVirus Respirators
I use Simpify 3D on a MakerGear M2 printer. I now use a hair band through the side holes and loop them. Then I take a head band and cut it and connect it to the loops with a clasp I made. Really comfortable. Let me know if you want images of final product.
Tom
Tom
- Mon Mar 30, 2020 8:14 pm
- Forum: General Discussion
- Topic: 3D Printed CoronaVirus Respirators
- Replies: 18
- Views: 27982
Re: 3D Printed CoronaVirus Respirators
I have been using another design also by a Dentist: https://firedbycorona.com This mask takes 3.5 hours to print and I have been using ESun PetG. The fit is great. I just have to sand a little on the cheek for a great fit. For a filter, I used a 3M filter by Filtrete: Advanced Allergen, Bacteria & V...
- Thu Jan 28, 2016 7:17 pm
- Forum: Tech Support
- Topic: Is my hot end failing?
- Replies: 5
- Views: 7375
Re: Is my hot end failing?
Your problem sounds similar to the one I just had. I measured the outside temp with a multimeter and got around 220 instead of the 250 reported. I had a clicking sound which I thought was the gear not able to push the filiment through the nozzle (V4) because the temp was too low. To make a long stor...
- Thu Jan 28, 2016 7:00 pm
- Forum: Tech Support
- Topic: Rambo Issues
- Replies: 9
- Views: 8862
Re: Rambo Issues
All fixed!!! Problem was the pinion gear was stripped on the extruder motor. Replacement gear $5.00 from Makergear. Life is good again
- Tue Jan 12, 2016 4:29 am
- Forum: Tech Support
- Topic: Rambo Issues
- Replies: 9
- Views: 8862
Re: Rambo Issues
I have tried everything. I used guitar wire to pass through the hot end. Used the cleaning filiment from ESun and tried PLA filiment. Some would extrude a little then stop with the filiment drive clicking. Per Josh I measured the thermistor temp in the hot end and it is at least 25 * degrees cooler ...
- Sun Jan 10, 2016 11:48 pm
- Forum: Tech Support
- Topic: Rambo Issues
- Replies: 9
- Views: 8862
Re: Rambo Issues
That's what I thought so had both loosened and tighter it but it made no difference unless there is some trick to it. The gear imprint seems the same regardless of tension.
- Sun Jan 10, 2016 11:16 pm
- Forum: Tech Support
- Topic: Rambo Issues
- Replies: 9
- Views: 8862
Re: Rambo Issues
Hi Tim, Thanks for you comments. I found out the replacement board had a blown fuse and that is why it stopped working. Replaced it with the original and now it is connected. I believe you are right on the money and it is not the board. What is happening is when the PetG(right again) is threaded int...
- Sat Jan 09, 2016 9:12 pm
- Forum: Tech Support
- Topic: Rambo Issues
- Replies: 9
- Views: 8862
Rambo Issues
Hi All, I am hoping the forum can point me in the right direction. I have had the M2 for over a year with no problems. Recently the extruder clogged so I figured now is the time to upgrade to the V4. Ordered the kit and worked great for a few weeks. Then at the end of a print I got a birds nest. The...
- Fri Jul 17, 2015 5:13 am
- Forum: Filament
- Topic: PetG White layer bonding problem
- Replies: 6
- Views: 11006
Re: PetG White layer bonding problem
I was wondering if the temp needed to be higher. What temp for the white petG is everyone using and how high can I safety go with the stock VB3.