Search found 19 matches

by HadMatter
Sun Feb 28, 2016 8:38 pm
Forum: Tech Support
Topic: Filament drive replacement print
Replies: 7
Views: 9079

Re: Filament drive replacement print

Is this a printable part? If so would anyone mind sharing the link to the file?
Thanks.
by HadMatter
Wed Nov 05, 2014 10:16 pm
Forum: M2 Dual Extruder
Topic: v4 Status
Replies: 132
Views: 148406

Re: v4 Status

woot!!!
by HadMatter
Wed Nov 05, 2014 10:12 pm
Forum: How-to/Guides/Tips
Topic: acetone vapor smoothing (again)
Replies: 2
Views: 6295

Re: acetone vapor smoothing (again)

brilliant!
by HadMatter
Wed Nov 05, 2014 10:11 pm
Forum: General Discussion
Topic: type of oil to lubricate rails in m2
Replies: 13
Views: 18068

Re: type of oil to lubricate rails in m2

Local Music shops or amazon, Trombone Slide Cream. its the way to go.
by HadMatter
Mon Nov 03, 2014 8:42 pm
Forum: Tech Support
Topic: M2 RAMBo And MW SE-450-24 PSU Wiring diagram or schematics
Replies: 10
Views: 16609

Re: M2 RAMBo And MW SE-450-24 PSU Wiring diagram or schemati

I apologize, I failed to ever post conclusive information. probably two or three days from my last post on this topic, I had successfully identified the proper terminations and their purposes.
It's been too long to really say more than, it was just a swapped conductor.
by HadMatter
Fri Oct 10, 2014 6:22 pm
Forum: General Discussion
Topic: type of oil to lubricate rails in m2
Replies: 13
Views: 18068

Re: type of oil to lubricate rails in m2

I used to played trombone for 3 years, I would Imagine the Slide Oil or Slide Cream Would be hard to beat. Caution Trombone Tuning Slide Grease Is Not the same thing im referring to. It is for a seperate part of the instrument, and is nothing more than Petroleum jelly. Also having owned A nice fusbo...
by HadMatter
Mon Sep 29, 2014 6:15 pm
Forum: General Discussion
Topic: Prints with rounded/arched bridging
Replies: 5
Views: 7767

Re: Prints with rounded/arched bridging

Thank you all for your replies, We will try to get a picture up asap as to better illustrate our complications. Also we are printing PLA 1.75mm with a .35mm extruder nozzle and set at .3mm in Simplify 3D. Also Consider it more to be sagging/separating exterior layers of this particular print. We are...
by HadMatter
Thu Sep 25, 2014 9:26 pm
Forum: General Discussion
Topic: Prints with rounded/arched bridging
Replies: 5
Views: 7767

Prints with rounded/arched bridging

Hello, We are experiencing difficulties printing objects with rounded corners, typically the layers sagging, sometimes a little sometime a lot. We print with simplify 3d and love it but this issue has been recurring throughout the entire duration we have been printing. Has anyone had issues with arc...
by HadMatter
Thu Sep 25, 2014 9:17 pm
Forum: How-to/Guides/Tips
Topic: Stop your geared stepped motors from grinding!
Replies: 6
Views: 9568

Stop your geared stepped motors from grinding!

Check the endstops!! The M2 I am familiar with had been grinding gears from improper endstop positioning. They can become contorted and bend, if this happens carefully (perhaps with needle nose pliers) bend the endstops back into a positon as where, once the bed plate hit them, you should hear/feel ...
by HadMatter
Sun Aug 10, 2014 1:35 am
Forum: Tech Support
Topic: Y Axis Motor issue
Replies: 4
Views: 7139

Re: Y Axis Motor issue

Gents,

Thank You for the responses.

It actually prints well. It has recently begun to over extend the Y Axis and make the grinding noise just before it starts.

I will look at s3d, but it did not do this previously.

Thank You