Search found 65 matches

by Spencer
Wed Oct 03, 2018 11:56 pm
Forum: Tech Support
Topic: Simplify 3d fff settings
Replies: 9
Views: 456

Re: Simplify 3d fff settings

No Problem, I know the level of frustration with S3D.. and guess what, they claim to be releasing a new version and I am sure everything I have leaned will be null and void when 4.1 is released.. Oh and there will be no documentation.. :? Haha right? I heard these zits and blops just go away if you...
by Spencer
Wed Oct 03, 2018 10:32 pm
Forum: Tech Support
Topic: Simplify 3d fff settings
Replies: 9
Views: 456

Re: Simplify 3d fff settings

Well I am not judging, and not an expert, just stating the facts I learned over the past 6 months in one statement. To reload the original config file, go to Help > Configuration Assistant and walk through the wizard to install the default profile. It will not alter the profiles you already have. I...
by Spencer
Wed Oct 03, 2018 10:31 pm
Forum: Tech Support
Topic: Simplify 3d fff settings
Replies: 9
Views: 456

Re: Simplify 3d fff settings

Phil wrote:
Mon Oct 01, 2018 5:03 pm
Jules put up a pretty good file quite some time ago. I think it was in a thread titled "Black eSun PETG..." I am sure you can find it; lots of other good stuff in the thread, too. It should make a good start point at any rate.
Thanks, I'll go looking for it!
by Spencer
Wed Oct 03, 2018 9:37 pm
Forum: Software
Topic: Looking for a .fff file for a M2 Rev. D
Replies: 3
Views: 295

Re: Looking for a .fff file for a M2 Rev. D

I'm not sure what you mean by "outdated" in reference to Insta's files. They should be good for any M2 Rev. D or E; basically any M2 with a v4 extruder on it. I don't remember when MakerGear started the official revision letters, but I'm pretty sure it was well into the v4 era. As far as the FFF fi...
by Spencer
Mon Oct 01, 2018 12:12 pm
Forum: Software
Topic: Looking for a .fff file for a M2 Rev. D
Replies: 3
Views: 295

Looking for a .fff file for a M2 Rev. D

Hey guys. I've posted in tech support but I think this is the better board to post it. I'm looking for a working M2 Rev. D Simplify3d .fff file. I've tweaked mine so much that nothing I do shows any promising results. I just need a solid baseline so I can go from there. Plus this will let me know if...
by Spencer
Mon Oct 01, 2018 12:02 pm
Forum: Tech Support
Topic: Simplify 3d fff settings
Replies: 9
Views: 456

Re: Simplify 3d fff settings

Sorry to tell you this, but 3D printing is not like printing a word doc.. it is trial and error until you learn how to set up your slicer.. Every model is a little different.. on size does not fit all.. Rather steep learning curve, especially with S3D.. I just did this starting last Feb.. so stop l...
by Spencer
Mon Oct 01, 2018 1:37 am
Forum: Tech Support
Topic: Simplify 3d fff settings
Replies: 9
Views: 456

Simplify 3d fff settings

Hey guys, I've been going crazy trying to find a good .fff file for my M2 Rev. D. The one I've been using wasn't that great so I've been trying to find another one. The default one that comes with simplify 3D produced me a poor benchy. The Makergear website only has .fff files for M3's, which I've t...
by Spencer
Mon Nov 06, 2017 11:47 pm
Forum: Tech Support
Topic: Every print I make gets these little raised bumps.
Replies: 1
Views: 441

Every print I make gets these little raised bumps.

https://imgur.com/a/wNUk9

I have a M2 Rev E. Every print gets these bumps in the same exact spot. Any ideas?
by Spencer
Tue May 23, 2017 7:10 pm
Forum: Tech Support
Topic: Fan turning on and off during prnit
Replies: 0
Views: 919

Fan turning on and off during prnit

Hey guys. On my Rev E. My fan motors will turn on and off every few seconds, for a second. Is this normal for the Rev. E? Or is there a loose wire somewhere I need to check. Thanks

Spencer
by Spencer
Thu May 11, 2017 2:41 am
Forum: Tech Support
Topic: Rev E. prints slower than Rev. D.
Replies: 4
Views: 1840

Re: Rev E. prints slower than Rev. D.

Wait, I thought the firmware was in the machine itself. How would I update that?
insta wrote:The heavier bed was paired with slower acceleration. It's a firmware / GCode adjustment if you want to raise the speed back up.

http://marlinfw.org/docs/gcode/M204.html