Search found 86 matches

by Hugs
Sun Apr 01, 2018 3:33 pm
Forum: Software
Topic: Accessing Octoprint
Replies: 2
Views: 656

Re: Accessing Octoprint

You're changing the port so check your /etc/haproxy/haproxy.cfg file. You'll probably have to add the different port there. I'm just using the standard 8080 so this is the binding section from mine: [...] frontend public bind *:80 use_backend webcam if { path_beg /webcam/ } default_backend octoprint...
by Hugs
Sun Feb 18, 2018 5:55 pm
Forum: General Discussion
Topic: IDeas/Help designing Stone/brick veneer
Replies: 1
Views: 711

Re: IDeas/Help designing Stone/brick veneer

OpenSCAD has a Surface function that may be of interest. I just did a quick Google image search for "brick heightmap" Obviously not the ideal map but just as a starting point to give you an idea: surface(file="brick.png", center=true, convexity=5); %translate([0,0,2]) cube([100,100,1], center=true);...
by Hugs
Tue Feb 06, 2018 5:19 pm
Forum: M3-ID
Topic: Printing with Right head, T1
Replies: 4
Views: 1829

Re: Printing with Right head, T1

[...]but in octoprint, im assuming the left hottend temp is being displayed, i have no control over the Right Hotend. I'm being Captain Obvious here, but did you set the number of extruders to 2 in the Octoprint printer profile? dual-extuders.PNG You should see both extruders in the Control tab: du...
by Hugs
Mon Nov 13, 2017 9:17 pm
Forum: General Discussion
Topic: How Do I Get Rid of fine spider threads between parts?
Replies: 5
Views: 1812

Re: How Do I Get Rid of fine spider threads between parts?

Explorer74 wrote:Is there a good way to remove them?
Try a hair dryer or heat gun. Works a treat on PETg where stringiness is a problem for some prints.
by Hugs
Wed Nov 01, 2017 12:08 pm
Forum: Getting Started
Topic: Do I need the bed factory applied Kapton for PLA?
Replies: 11
Views: 5210

Re: Do I need the bed factory applied Kapton for PLA?

Would you mind describing how you put down the film without bubbles? I can see that you use a piece of dowel rod to stretch out the filament between the roll and the near edge of the jig, but then what do you do to smooth out the film on the glass? The glass gets a spritz of distilled water with a ...
by Hugs
Sat Oct 21, 2017 2:39 pm
Forum: M3-ID
Topic: MAKERGEAR M3-ID reviews
Replies: 34
Views: 14667

Re: MAKERGEAR M3-ID reviews

Is the tape necessary for the prints? It's scraped in 3 places right now...Is the tape essential, can we take it off? Consider the tape a consumable. Some people have success with bare glass and some sort of adhesive but I've had many successful prints with the Kapton. I've since switched to one of...
by Hugs
Mon Aug 14, 2017 3:08 pm
Forum: M2 Dual Extruder
Topic: second extruder not working properly
Replies: 4
Views: 2259

Re: second extruder not working properly

You might want to make sure you have the connector plugged in correctly...which is reversed compared to extruder 0. If you don't, extruder 1 will retract instead of extrude (because they feed from different sides of the gear). I had a similar problem when I installed my dual kit. Here's a picture of...
by Hugs
Sun Aug 13, 2017 2:30 pm
Forum: Tech Support
Topic: octoprint and reprap graphic controller (the makergear one)
Replies: 7
Views: 4040

Re: octoprint and reprap graphic controller (the makergear o

[...]turning on the bed heater with the LCD and then trying to run a print with the Octopi Pi3. I just printed a calibration cube by setting the nozzle and bed temps with the LCD then starting the print via OctoPrint and I didn't have any issues. Is it a consistent error? Maybe a bad USB cable or c...
by Hugs
Sun Aug 13, 2017 12:46 pm
Forum: Tech Support
Topic: octoprint and reprap graphic controller (the makergear one)
Replies: 7
Views: 4040

Re: octoprint and reprap graphic controller (the makergear o

How are you running OctoPrint?

I have a couple OctoPrint plugins that send info to the LCD so they definitely work together. I'm running a dedicated OctoPi on a Raspberry Pi 3 though.
by Hugs
Tue Jul 04, 2017 1:31 pm
Forum: Modifications
Topic: Dual extruder firmware upgrade
Replies: 1
Views: 1207

Re: Dual extruder firmware upgrade

(If I don't have to do this to use the dual printer, then that solves my problems) You do indeed have to flash the firmware with that version enable the second extruder and make it visible to the software. After downloading this and opening it with the Arduino IDE (tested in 1.6.13 and 1.8.3) To my...