Search found 59 matches

by KaiborgStudios
Wed May 19, 2021 3:54 am
Forum: Tech Support
Topic: WARNING: Firmware Unresponsive
Replies: 2
Views: 6311

Re: WARNING: Firmware Unresponsive

Can do! Once it happens again I'll snag that info.
by KaiborgStudios
Sat May 15, 2021 2:20 am
Forum: Tech Support
Topic: Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
Replies: 1
Views: 5231

Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)

I've had this reoccurring issue plaguing one of my M2 Rev. E. Here is my previous thread: http://forum.makergear.com/viewtopic.php?f=7&t=8154 The solution last time was repairing an partial break in the wiring harness causing the temp probe to mintemp. I repaired the area, and it continued to work f...
by KaiborgStudios
Sat May 15, 2021 1:54 am
Forum: Tech Support
Topic: WARNING: Firmware Unresponsive
Replies: 2
Views: 6311

WARNING: Firmware Unresponsive

Having this issue intermittently on one of my M2 Rev. E. It will pause the print , and sit there spitting out this error. Any ideas?

Thanks!
Cameron
by KaiborgStudios
Sun Jun 14, 2020 2:49 am
Forum: Tech Support
Topic: Filament Runout Sensor without LCD
Replies: 3
Views: 6011

Re: Filament Runout Sensor without LCD

Wanted to bump this, any thoughts?

Cameron
by KaiborgStudios
Thu May 28, 2020 1:42 pm
Forum: Tech Support
Topic: Filament Runout Sensor without LCD
Replies: 3
Views: 6011

Filament Runout Sensor without LCD

Currently working on adding a filament runout sensor to my M2 Rev. E. I've find a few how to's for the wiring and the basic firmware modifications: http://forum.makergear.com/viewtopic.php?f=10&t=6408 https://www.thingiverse.com/thing:1887387 https://forum.lulzbot.com/t/simple-filament-runout-sensor...
by KaiborgStudios
Mon May 18, 2020 11:37 pm
Forum: Tech Support
Topic: Z motor catch and dropping only during startup sequence.
Replies: 11
Views: 13257

Re: Z motor catch and dropping only during startup sequence.

what are we looking at???? The reason the issue was only arising after homing and raising the build plate. Once the X axis was home and the lead screw knob turned clockwise to raise the plate, an indentation in the makergear logo on the knob was grabbing the left extruder's thermistor wire, stallin...
by KaiborgStudios
Mon May 18, 2020 11:33 pm
Forum: Tech Support
Topic: Z motor catch and dropping only during startup sequence.
Replies: 11
Views: 13257

Re: Z motor catch and dropping only during startup sequence.

not consulting Occam's Razor Well, that's obvious! In retrospect, anyway. [grin] The third item in the Debugging Rules poster over my workbench applies: "Quit thinking and look". It seems I can always come up with a complex fault that doesn't actually match the obvious-in-retrospect evidence, alas....
by KaiborgStudios
Mon May 18, 2020 1:24 am
Forum: Tech Support
Topic: Z motor catch and dropping only during startup sequence.
Replies: 11
Views: 13257

Re: Z motor catch and dropping only during startup sequence.

accelerations during homing to match that of jogging Now that I look at the source again, at least for (obsolete) Marlin 1.1.0, there's only one acceleration setting. Seeing as how homing works, it's probably OK. I appear to have made the mistake of not consulting Occam's Razor, but the problem is ...
by KaiborgStudios
Sat May 16, 2020 3:51 am
Forum: Tech Support
Topic: Z motor catch and dropping only during startup sequence.
Replies: 11
Views: 13257

Re: Z motor catch and dropping only during startup sequence.

Another bit of info. I had a thought for another test; manually pressing the z stop with the z axis only half way down the z screw. Same exact issue, immediately catches upon raising the platform post homing. So that proves there is no specific spot that causing it, to motor simply cannot lift the b...
by KaiborgStudios
Sat May 16, 2020 3:33 am
Forum: Tech Support
Topic: Z motor catch and dropping only during startup sequence.
Replies: 11
Views: 13257

Re: Z motor catch and dropping only during startup sequence.

cannot make it catch by any other means What's different: the different speeds & accelerations used during homing vs. manual jogging vs. normal operation. Thank you as always Ed! I followed your cleaning instructions and reassembled, no luck. I felt little to no resistance on the linear rails, drow...