Search found 67 matches

by steve220
Fri Sep 28, 2018 1:19 pm
Forum: Tech Support
Topic: Increase baud rate?
Replies: 4
Views: 6874

Re: Increase baud rate?

BTW, this is not my image, I copied it from the thread referenced above. The left print is printed from the SD card slot and the right is the same gcode printed from Octoprint. I'm seeing this same kind of effect on a small number of prints, typically those with a lot of round shapes and curves. I w...
by steve220
Fri Sep 28, 2018 1:14 pm
Forum: Tech Support
Topic: Increase baud rate?
Replies: 4
Views: 6874

Re: Increase baud rate?

Great question Ed, There are a few threads regarding lower print quality using Octoprint VS printing from an SD card using the same gcode file. Here is one: https://discourse.octoprint.org/t/poor-print-quality-mp-mini-delta-octoprint-vs-sd-card/3743/40 I am experiencing the same types of artifacts o...
by steve220
Fri Sep 28, 2018 5:08 am
Forum: Tech Support
Topic: Increase baud rate?
Replies: 4
Views: 6874

Increase baud rate?

Is it possible to change the default baud rate of the V4 without doing a firmware recompile?
It is 115000 by default and I would like to change it to 250000.
by steve220
Fri Sep 28, 2018 5:00 am
Forum: General Discussion
Topic: Timelapse mod for the M2/3 with Octoprint?
Replies: 8
Views: 18110

Re: Timelapse mod for the M2/3 with Octoprint?

So sorry! I hadn’t logged on in a while.
Yes, that is the correct configuration.
by steve220
Sat Apr 14, 2018 6:12 am
Forum: General Discussion
Topic: Timelapse mod for the M2/3 with Octoprint?
Replies: 8
Views: 18110

Re: Timelapse mod for the M2/3 with Octoprint?

Just started using the Octolapse plugin. Very cool with lot's of options. If you're interested, you can view a sample timelapse on my latest thingiverse make:
https://www.thingiverse.com/make:477876

Direct link to the youtube vid:
https://www.youtube.com/watch?v=k0rlxSmwf_0
by steve220
Mon Nov 06, 2017 12:07 am
Forum: Tech Support
Topic: Annoying Rattle
Replies: 4
Views: 7231

Re: Annoying Rattle

Thanks for all of the suggestions. The washers are tight. I switched filament and the issue went away. I switched back and the issue came back. Seems weird that it could be filament related.
by steve220
Mon Oct 30, 2017 1:46 pm
Forum: Tech Support
Topic: Annoying Rattle
Replies: 4
Views: 7231

Annoying Rattle

I'd appreciate thoughts on an annoying rattle or buzzing I'm hearing. It comes and goes with little rhyme or reason that I can ID. I've replaced the fans, so have eliminated them as a source. It sounds like it is coming from the extruder motor. There do not appear to be any ill effects to the print ...
by steve220
Fri Sep 22, 2017 12:46 pm
Forum: General Discussion
Topic: Printing Filament Drive
Replies: 4
Views: 9794

Re: Printing Filament Drive

Thanks everyone. I'll have to see about picking up some ePC!
by steve220
Wed Sep 20, 2017 6:37 am
Forum: General Discussion
Topic: Printing Filament Drive
Replies: 4
Views: 9794

Printing Filament Drive

Filament drive has finally worn out. Are there recommended settings for fill, layer height, supports, etc?
by steve220
Wed Aug 16, 2017 3:40 am
Forum: Tech Support
Topic: Hotend Cooling Down During Print
Replies: 4
Views: 7482

Re: Hotend Cooling Down During Print

Had to replace mine recently too. Zemlin, that's a great tip!