Search found 67 matches
- Fri Sep 28, 2018 1:19 pm
- Forum: Tech Support
- Topic: Increase baud rate?
- Replies: 4
- Views: 6973
Re: Increase baud rate?
BTW, this is not my image, I copied it from the thread referenced above. The left print is printed from the SD card slot and the right is the same gcode printed from Octoprint. I'm seeing this same kind of effect on a small number of prints, typically those with a lot of round shapes and curves. I w...
- Fri Sep 28, 2018 1:14 pm
- Forum: Tech Support
- Topic: Increase baud rate?
- Replies: 4
- Views: 6973
Re: Increase baud rate?
Great question Ed, There are a few threads regarding lower print quality using Octoprint VS printing from an SD card using the same gcode file. Here is one: https://discourse.octoprint.org/t/poor-print-quality-mp-mini-delta-octoprint-vs-sd-card/3743/40 I am experiencing the same types of artifacts o...
- Fri Sep 28, 2018 5:08 am
- Forum: Tech Support
- Topic: Increase baud rate?
- Replies: 4
- Views: 6973
Increase baud rate?
Is it possible to change the default baud rate of the V4 without doing a firmware recompile?
It is 115000 by default and I would like to change it to 250000.
It is 115000 by default and I would like to change it to 250000.
- Fri Sep 28, 2018 5:00 am
- Forum: General Discussion
- Topic: Timelapse mod for the M2/3 with Octoprint?
- Replies: 8
- Views: 18386
Re: Timelapse mod for the M2/3 with Octoprint?
So sorry! I hadn’t logged on in a while.
Yes, that is the correct configuration.
Yes, that is the correct configuration.
- Sat Apr 14, 2018 6:12 am
- Forum: General Discussion
- Topic: Timelapse mod for the M2/3 with Octoprint?
- Replies: 8
- Views: 18386
Re: Timelapse mod for the M2/3 with Octoprint?
Just started using the Octolapse plugin. Very cool with lot's of options. If you're interested, you can view a sample timelapse on my latest thingiverse make:
https://www.thingiverse.com/make:477876
Direct link to the youtube vid:
https://www.youtube.com/watch?v=k0rlxSmwf_0
https://www.thingiverse.com/make:477876
Direct link to the youtube vid:
https://www.youtube.com/watch?v=k0rlxSmwf_0
- Mon Nov 06, 2017 12:07 am
- Forum: Tech Support
- Topic: Annoying Rattle
- Replies: 4
- Views: 7296
Re: Annoying Rattle
Thanks for all of the suggestions. The washers are tight. I switched filament and the issue went away. I switched back and the issue came back. Seems weird that it could be filament related.
- Mon Oct 30, 2017 1:46 pm
- Forum: Tech Support
- Topic: Annoying Rattle
- Replies: 4
- Views: 7296
Annoying Rattle
I'd appreciate thoughts on an annoying rattle or buzzing I'm hearing. It comes and goes with little rhyme or reason that I can ID. I've replaced the fans, so have eliminated them as a source. It sounds like it is coming from the extruder motor. There do not appear to be any ill effects to the print ...
- Fri Sep 22, 2017 12:46 pm
- Forum: General Discussion
- Topic: Printing Filament Drive
- Replies: 4
- Views: 9887
Re: Printing Filament Drive
Thanks everyone. I'll have to see about picking up some ePC!
- Wed Sep 20, 2017 6:37 am
- Forum: General Discussion
- Topic: Printing Filament Drive
- Replies: 4
- Views: 9887
Printing Filament Drive
Filament drive has finally worn out. Are there recommended settings for fill, layer height, supports, etc?
- Wed Aug 16, 2017 3:40 am
- Forum: Tech Support
- Topic: Hotend Cooling Down During Print
- Replies: 4
- Views: 7553
Re: Hotend Cooling Down During Print
Had to replace mine recently too. Zemlin, that's a great tip!