Search found 487 matches

by airscapes
Tue Apr 06, 2021 4:05 am
Forum: Tech Support
Topic: Uneven extrusion?
Replies: 2
Views: 32

Re: Uneven extrusion?

Glass bed loose? Jerk wrong due to fat finger when setting Z offset?
by airscapes
Mon Mar 15, 2021 6:23 pm
Forum: Tech Support
Topic: Firmware and Octoprint Updates
Replies: 9
Views: 1139

Re: Firmware and Octoprint Updates

Have you considered just buying a new sd card and loading up the new Octoprint.. I personally have not upgraded OP I use with my M2 since installing it in 2019 as I don't use plugins and all is still working just fine. However that would be the route I would take.. Keep the old card and try installi...
by airscapes
Thu Mar 11, 2021 9:47 pm
Forum: Tech Support
Topic: Firmware and Octoprint Updates
Replies: 9
Views: 1139

Re: Firmware and Octoprint Updates

I would also email MG support directly.
by airscapes
Sun Feb 14, 2021 11:16 pm
Forum: Modifications
Topic: Installing an E3D V6 today, what do I need to know?
Replies: 5
Views: 3653

Re: Installing an E3D V6 today, what do I need to know?

Hey Helifrek How did the hot end upgrade turn out? You mentioned that you had to print a mount. Would you mind posting the file you used? Maybe a couple pictures would be helpful. I been haveing some issues printing with PETG and I think the V4 hot end is just not up to the job. No, print PETG all ...
by airscapes
Sat Jan 16, 2021 4:50 am
Forum: Tech Support
Topic: Resonances in X & Y Axis?
Replies: 5
Views: 1523

Re: Resonances in X & Y Axis?

could be the model was exported with too much detail, also check your M503 output .. jerk could have gotten accidently hosed, I know I had a similar issues when I had a fat finger entry..
by airscapes
Sat Jan 09, 2021 5:57 pm
Forum: M3-ID
Topic: pause reload and continue
Replies: 2
Views: 1259

Re: pause reload and continue

If you are doing this because you are about to run out and just want to keep going with a fresh roll of the same stuff you can do the following. When you have about a foot of the old left to go, hang you new roll, pull the remaining filament out of the Bowden tube, slide in your new filament, then c...
by airscapes
Sat Jan 09, 2021 12:10 am
Forum: Software
Topic: Prusaslicer 2.x
Replies: 50
Views: 10325

Re: Prusaslicer 2.x

The more I use PS the less I feel like using PS..
by airscapes
Fri Jan 08, 2021 5:05 am
Forum: Software
Topic: Prusaslicer 2.x
Replies: 50
Views: 10325

Re: Prusaslicer 2.x

Ah I see.. As to the length of time.. there are a lot of speed settings and the don't all default to a percentage of the over all speed.. so you have to mess with them all. And you have to decide if you want to enter actual speed values or % or one of the many speed settings.. Not that this is a bad...
by airscapes
Thu Jan 07, 2021 11:42 pm
Forum: Software
Topic: Prusaslicer 2.x
Replies: 50
Views: 10325

Re: Prusaslicer 2.x

What is the variable layer process.. is that something that can be configured or just integral to the slicer? I can not find anything in any of the tabs that sounds like that.
by airscapes
Thu Jan 07, 2021 4:50 pm
Forum: Software
Topic: Prusaslicer 2.x
Replies: 50
Views: 10325

Re: Prusaslicer 2.x

Yup! I still keep going back to the Devil I know..