Search found 315 matches

by airscapes
Tue May 21, 2019 2:45 pm
Forum: Filament
Topic: Nylon
Replies: 27
Views: 2279

Re: Nylon

This bed did not really work for me any batter than glass and glue.. Maybe I didn't work at it long enough but Polymide tape works better for my non production environment. You also can't print anything that needs a hot bed (over 80) or the plate will warp.. Bed flatness is just in the stated tolera...
by airscapes
Fri May 17, 2019 7:36 pm
Forum: General Discussion
Topic: Anyone have an Ultra One yet?
Replies: 11
Views: 242

Re: Anyone have an Ultra One yet?

Hey Tyler, is this compared to the M2 for the same part with the same speed settings?
What are the M205 settings of the Ultra?
by airscapes
Fri May 17, 2019 5:56 pm
Forum: Tech Support
Topic: Jittery temps
Replies: 1
Views: 26

Re: Jittery temps

Yup most likely, order more than one they don't go bad sitting on your shelf so you have it when you need it! Once you get it you should do an auto pid calibration. Not sure how to do it on a dual extruder but on the single of the M2 From terminal enter M303 It will turn on the extruder and do some ...
by airscapes
Thu May 16, 2019 3:39 pm
Forum: How-to/Guides/Tips
Topic: Eliminate the PSU fan noise
Replies: 3
Views: 45

Re: Eliminate the PSU fan noise

A better picture of ghosting, this is abs was printed at 50mmS with 70% reduction on perimeter
I have read that printer with moving beds suffer more from this artifact than other designs so may not have anything to do with dampers..
ghosting2.jpg
by airscapes
Thu May 16, 2019 2:31 pm
Forum: How-to/Guides/Tips
Topic: Eliminate the PSU fan noise
Replies: 3
Views: 45

Re: Eliminate the PSU fan noise

If you are talking about the rubber damper sandwiched in metal, that attach to the motor with 2 screws and the frame with 2 screws, I would not suggest it. The motor will cock to one side even with shims. I made Ninjaflex dampers and screw head isolation washers that quiet the machine just as much a...
by airscapes
Wed May 01, 2019 8:34 pm
Forum: General Discussion
Topic: Anyone have an Ultra One yet?
Replies: 11
Views: 242

Re: Anyone have an Ultra One yet?

Um. this is the $10,000 printer?? Why not call tech support.. I would be flippin
by airscapes
Thu Apr 18, 2019 1:41 pm
Forum: Pre-owned Gear
Topic: M3 ID For Sale
Replies: 4
Views: 205

Re: M3 ID For Sale

where are you located?
by airscapes
Sat Apr 13, 2019 5:29 pm
Forum: Tech Support
Topic: Printer unable to complete prints
Replies: 1
Views: 113

Re: Printer unable to complete prints

I would call customer support, they may even answer on Saturday.. Support: 216-508-4025 (9AM - 4PM EST).
by airscapes
Sun Apr 07, 2019 1:20 am
Forum: Printed Object Showcase
Topic: M3 ID REV 0 Enclosure made with printed hardware
Replies: 5
Views: 381

Re: M3 ID REV 0 Enclosure made with printed hardware

No, they did not say put it in an open ended box.. they said cover it with a box.. I printed a box that split even with an enclosure. For the noise I printed dampers our of ninjaflex and placed them between the X an Y stepper and ninjaflex washers for under the screws. I have attached the files if y...
by airscapes
Tue Apr 02, 2019 1:18 pm
Forum: Printed Object Showcase
Topic: M3 ID REV 0 Enclosure made with printed hardware
Replies: 5
Views: 381

Re: M3 ID REV 0 Enclosure made with printed hardware

Very cool looking enclose! My enclosure for my M2 is not heated. Since the bed temp for ABS is 110C, I just fire the heater up while I am prepping the model and have not had too much trouble with ABS. A 8x8x8x4 open ended box I made last year did split in a couple of places but for smaller items I h...