Search found 890 matches

by sthone
Wed Jan 22, 2020 3:23 am
Forum: Tech Support
Topic: Did I botch something and if so how bad?
Replies: 4
Views: 874

Re: Did I botch something and if so how bad?

Untitled-1.jpg
The Red circle is where you set the temp. and the blue circle is where you would extrude 100mm of filament once the temp is anywhere above 170.
by sthone
Thu Jan 16, 2020 7:27 pm
Forum: Tech Support
Topic: Has anyone changed the fan in their power supply?
Replies: 24
Views: 14132

Re: Has anyone changed the fan in their power supply?

I can't help you with the specs but I've had the Noctura's in all 3 of my power supplies and I've never had an issue.... well I have to assume they are running because they sure can't be heard.
by sthone
Sun Dec 29, 2019 7:13 pm
Forum: Tech Support
Topic: Remap extruder pins
Replies: 6
Views: 647

Re: Remap extruder pins

I'm no expert but I think if you plug it into the other port you just need to tell your slicer to use tool 2 instead of tool 1 from now on. I wouldn't think you need to rewrite the firmware.
by sthone
Wed Dec 11, 2019 1:51 pm
Forum: Tech Support
Topic: Petg extruding problems
Replies: 13
Views: 1206

Re: Petg extruding problems

So the whole blow torch method I’ve never tried kinda confused about. Do I just heat the shit out of it and call it good with the blow torch? Was going to go back to play and see if I have the same problem Basically yeah... you take the nozzle off and just heat it up to burn out any crap that is in...
by sthone
Tue Dec 10, 2019 1:57 pm
Forum: M3-ID
Topic: Octoprint module SD card access?
Replies: 3
Views: 614

Re: Octoprint module SD card access?

The SD card is in the Raspberry Pi. (I assume they are using Pi's) The Pi is housed in the smaller box on the base of the printer. (the one on the left) You would need to remove the SD card from the PI and then follow this tutorial to copy it. https://www.howtogeek.com/341944/how-to-clone-your-raspb...
by sthone
Tue Dec 10, 2019 1:41 pm
Forum: Tech Support
Topic: Petg extruding problems
Replies: 13
Views: 1206

Re: Petg extruding problems

Could be the filament.... try a different roll and see if that fixes the problem. Or if that's the only roll of PETG you have if it stops extruding a again measure the filament where it stop extruding and see if it's in spec. I've had a similar experience with ABS once and couldn't figure it out.......
by sthone
Tue Dec 10, 2019 1:35 pm
Forum: M2 Dual Extruder
Topic: Help needed updating Arduino 1.5.5r.2
Replies: 1
Views: 2314

Re: Help needed updating Arduino 1.5.5r.2

Hopefully you figured this out by now but here's the condensed version as I remember it. Unzip Arduino (it has to be 1.5.5) to a folder on your computer. Run Arduino when done. Under the "Tools" tab Set Board to (Arduino/Genuino Mega or Mega 2560) Set Processor to (Atmega2560 (Mega 2560) Set Port to...
by sthone
Fri Dec 06, 2019 7:54 pm
Forum: General Discussion
Topic: Ultra One First Impressions
Replies: 4
Views: 1265

Re: Ultra One First Impressions

Does the Ultra one still use printed parts such as the exruders or is it total different than the M2/3's? What does it use for hotends?

-Steve
by sthone
Fri Dec 06, 2019 7:51 pm
Forum: Tech Support
Topic: M2 Crazy Shake ?
Replies: 8
Views: 898

Re: M2 Crazy Shake ?

perhaps I need to change a code for that bigger nozzel? maybe the feedrate of the extruder? Yes... you can not run the same gcode for different sized nozzles. You need to go through and reslice the part and set the extrusion rate to the machine you are printing the part on if it has a different siz...
by sthone
Sat Nov 16, 2019 11:11 pm
Forum: Tech Support
Topic: Hotend Failures
Replies: 4
Views: 1141

Re: Hotend Failures

I don't know why the barrel would be spinning in the block but just so you know you can just buy new barrels (the snapped part) ... you don't need new hot ends every time. Just drop MG a email and tell them you need just the barrels.

-Steve