Search found 60 matches

by Ronnien55
Mon Jun 08, 2015 3:43 am
Forum: M2 Dual Extruder
Topic: Dual printing set up Saturday (thanks Scott D )
Replies: 9
Views: 7232

Re: Dual printing set up Saturday (thanks Scott D )

Extruder 1 is working fine, however extruder 0 is not extruding when it should. I have attached a picture.
by Ronnien55
Mon Jun 08, 2015 3:28 am
Forum: M2 Dual Extruder
Topic: Dual printing set up Saturday (thanks Scott D )
Replies: 9
Views: 7232

Re: Dual printing set up Saturday (thanks Scott D )

I'm not sure I understand your question. Dual extrusion is hard, because the non-printing extruder is constantly oozing and laying down unwanted dribbles. The only usable solutions I have found so far is, 1. Only use the second extruder for dissolvable filament, so that it doesn't matter that it's ...
by Ronnien55
Sun Jun 07, 2015 5:12 pm
Forum: M2 Dual Extruder
Topic: Dual printing set up Saturday (thanks Scott D )
Replies: 9
Views: 7232

Dual printing set up Saturday (thanks Scott D )

Well been just trying to get layers right and get the extruders to start when it is their time. Anyone have a good setup for shortening the delay between the switching of extruders and beginning printing? I am seeing separation between colors due to the extruder starting too late.
by Ronnien55
Mon May 25, 2015 6:57 pm
Forum: General Discussion
Topic: Extruder thermocouple
Replies: 4
Views: 1687

Re: Extruder thermocouple

I had the same problem, replace my cable between thermistor and RAMBo board and it is working fine. Lost my fan on the RAMBo box and am waiting on replacement fans.
by Ronnien55
Mon May 25, 2015 6:57 pm
Forum: General Discussion
Topic: Extruder thermocouple
Replies: 4
Views: 1687

Re: Extruder thermocouple

I had the same problem, replace my cable between thermistor and RAMBo board and it is working fine. Lost my fan on the RAMBo box and am waiting on replacement fans.
by Ronnien55
Sat May 16, 2015 1:54 pm
Forum: Tech Support
Topic: printer stopped during printing
Replies: 9
Views: 3224

Re: printer stopped during printing

thanks Dale, just read your posts, the bed was fine had just replaced last week. i found a bad wire to the extruder thermistor, i am in China at the moment and will replace upon my return. i will slow down my axis speeds. I did not see this problem till i started printing 23 hr parts, i had increase...
by Ronnien55
Thu May 14, 2015 11:11 pm
Forum: Tech Support
Topic: printer stopped during printing
Replies: 9
Views: 3224

Re: printer stopped during printing

If there are no error messages pointing you to the problem, check to be sure that the printer is still connected, via USB or Ethernet cable or—if a wireless model—that the Wi-Fi is enabled and that you're connected to the right network. The printer driver and software needs to be installed on the c...
by Ronnien55
Wed May 13, 2015 2:21 am
Forum: Software
Topic: M2 NinjaFlex Simplify3D Profile
Replies: 28
Views: 22986

Re: M2 NinjaFlex Simplify3D Profile

Definitely would like to get the Ninjaflex settings
by Ronnien55
Tue May 12, 2015 1:08 am
Forum: Tech Support
Topic: printer stopped during printing
Replies: 9
Views: 3224

Re: printer stopped during printing

RECEIVED: : Extruder switched off. MINTEMP triggered ! That indicates a broken wire in the extruder thermistor cable: open circuit = low temperature fault. The break can be anywhere, but recent experiences suggest starting at the thermistor itself. Turn off the power, unplug the extruder thermistor...
by Ronnien55
Mon May 11, 2015 11:47 pm
Forum: Tech Support
Topic: printer stopped during printing
Replies: 9
Views: 3224

Re: printer stopped during printing

there must be a bad wire in the bundle. when i heat up to temp and then swing the extruder along the x-axis it shuts down: SENT: M105 RECEIVED: ok T:221.6 /220.0 B:33.7 /0.0 @:27 RECEIVED: Error:0 RECEIVED: : Extruder switched off. MINTEMP triggered ! RECEIVED: Error:Printer stopped deu to errors. F...