Search found 266 matches
- Sun Jul 26, 2015 6:33 am
- Forum: Modifications
- Topic: nema17 dampers
- Replies: 160
- Views: 301644
Re: nema17 dampers
they seem to be Astrosyn MY17RMDAMP dampers. cheap enough to give it a try. I've read good things about them on the cnc forums. not just reducing sound but increasing quality... though you would think that there would be some quality loss due to the rubber gasket. if your in the uk, you can order th...
- Sat Jul 25, 2015 11:49 pm
- Forum: Modifications
- Topic: Zebra Plate
- Replies: 90
- Views: 103052
Re: Zebra Plate
I've been printing a lot of pla in the past week or two... more then I've printed in the past couple years to be frank...I have a lot of pla thats been sitting around for a few years..and never had use for it, and I am modeling prototypes for test fits, so its a perfect case for me to use it up. so ...
- Mon Jul 20, 2015 1:37 am
- Forum: Modifications
- Topic: Smoothie M2
- Replies: 119
- Views: 125615
Re: Smoothie M2
My only complaints are with S3d being a bit glitchy with smoothie. Glitchy in what way? if, for some reason, you start a print from s3d off the sd card, and you loose usb connectivity or the machine stops, the print will stop. sometimes S3D will just stop communicating with s3d causing he same issu...
- Sun Jul 19, 2015 5:42 am
- Forum: Tech Support
- Topic: Layer shifting
- Replies: 6
- Views: 8697
Re: Layer shifting
what is your travel speed set to, could you possibly be skipping steps?
Re: esun petg
petg .. Awsum stuff. and this is a great thread...after reading it all though, I pretty much followed jules settings from page 27 of the thread and got perfect prints.
using both esun from amazon..and esun-inland branded from microcenter petg with no changes. (all translucent colors)
using both esun from amazon..and esun-inland branded from microcenter petg with no changes. (all translucent colors)
- Sun Jul 19, 2015 5:19 am
- Forum: How-to/Guides/Tips
- Topic: Bed Leveling Cheat Sheet!
- Replies: 8
- Views: 13885
Re: Bed Leveling Cheat Sheet!
Posting this next to my pirate flag in my printing room.
arg! a pirate has to keep a level bed.
arg! a pirate has to keep a level bed.
- Sun Jul 19, 2015 5:11 am
- Forum: Modifications
- Topic: Smoothie M2
- Replies: 119
- Views: 125615
Re: Smoothie M2
Excellent detective work Tim. my x, y and z motors have no tags on them. so that's great information. i'll likely set my x and y current to 1.35A (90% of spec) and I will try the extruder at 1.0A (at spec but assuming smoothie is under rating a bit) I am very interested what your calibration says fo...
- Fri Jul 17, 2015 3:01 am
- Forum: Tech Support
- Topic: filament
- Replies: 7
- Views: 8548
Re: filament
I do find that each maker has diffrent optimal settings. i typicly write the temp and filiment size right on the spool once i figure it out again.
- Thu Jul 16, 2015 6:25 pm
- Forum: General Discussion
- Topic: Finally got my own!
- Replies: 11
- Views: 12237
Re: Finally got my own!
Been an ABS fan for a long time...but just started playing with PETG and loving life....
- Thu Jul 16, 2015 6:22 pm
- Forum: Tech Support
- Topic: filament
- Replies: 7
- Views: 8548
Re: filament
i've had good luck with (and in no partiular order)
folger tech
jet
makergear
makerbot
esun
folger tech
jet
makergear
makerbot
esun