Search found 92 matches

by kartcrg
Fri Feb 12, 2016 12:37 am
Forum: Other (off topic)
Topic: Product Design in Los Angeles
Replies: 3
Views: 3326

Re: Product Design in Los Angeles

Been keeping the facebook page updated with some 3D printing: https://www.facebook.com/brchndesignhouse/
by kartcrg
Sun Jan 24, 2016 9:06 am
Forum: Modifications
Topic: Metal Extruder Motor Mount - availabile
Replies: 35
Views: 18614

Re: Metal Extruder Motor Mount - availabile

creativedex wrote:Anyone mod the box yet?... It was nice to be able to flip the fans out of the way to clean or clear out the extruder but there just isnt enough wire length for them to move them.
I did but I just made it smaller really, doesn't give more wire length.
by kartcrg
Sat Jan 23, 2016 6:56 am
Forum: General Discussion
Topic: V4 Heat Creep - Melted Plastic Above Hot End
Replies: 20
Views: 8922

Re: V4 Heat Creep - Melted Plastic Above Hot End

Just an update.. Been running like this for a while. Life is good.

Image

Image

Image
by kartcrg
Sat Jan 23, 2016 2:25 am
Forum: General Discussion
Topic: Printing at 200 mm/s
Replies: 8
Views: 2972

Re: Printing at 200 mm/s

I would be curious to know if the rambo can actually process and print at 200mm or if it hits a buffer head at some point and you really are printing at 100 ? The two things I have noticed since my board swap are that 32 micro stepping helps with better dimensional accuracy and lower noise . And 60...
by kartcrg
Sat Jan 23, 2016 12:52 am
Forum: General Discussion
Topic: Securing your bed: Binder clips, none, or other?
Replies: 32
Views: 8030

Re: Securing your bed: Binder clips, none, or other?

Also anyone know what the latest revision to the filament drive was for? it was just posted 2 weeks ago That upload was a result of my request as I made some custom components that work with the drive they sent with my V4 (which we discovered was actually was the dual left drive after he uploaded t...
by kartcrg
Thu Jan 21, 2016 1:19 am
Forum: General Discussion
Topic: Printing at 200 mm/s
Replies: 8
Views: 2972

Re: Printing at 200 mm/s

PETG at 100 is ambitious. Especially if you have any increased infill width. Filament will be very likely to strip out in fast long runs. I'll watch out for that, thanks. I haven't tested much high speed printing with PETG as I usually don't have a need to go fast with it. It's convenient to rip PL...
by kartcrg
Sat Jan 16, 2016 11:01 am
Forum: General Discussion
Topic: Printing at 200 mm/s
Replies: 8
Views: 2972

Printing at 200 mm/s

I've been playing with draft quality print speed settings for PLA and get little noticeable quality difference with these settings relative to 100 mm/s and slightly smaller percentages. First layer speed is 60% and x & y acceleration is 2000. http://i.imgur.com/4k57P1El.png Also, I can print PETG at...
by kartcrg
Tue Jan 12, 2016 10:07 pm
Forum: Tech Support
Topic: Slicing Problem (unnecessary bridging)
Replies: 5
Views: 1462

Re: Slicing Problem (necessary bridging)

insta wrote:Can you change the slicer to discard segments instead of healing them? It's under "Advanced".
Tried that, does''t change anything.
by kartcrg
Tue Jan 12, 2016 6:49 am
Forum: Tech Support
Topic: Slicing Problem (unnecessary bridging)
Replies: 5
Views: 1462

Re: Slicing Problem (necessary bridging)

Thanks guys, appreciate it. I'll just do the 99% / 101% thing when it happens.
by kartcrg
Tue Jan 12, 2016 6:05 am
Forum: Tech Support
Topic: Slicing Problem (unnecessary bridging)
Replies: 5
Views: 1462

Slicing Problem (unnecessary bridging)

I can't figure out what is causing this. When sliced with my customized process, I get these random bridged sections where there should be nothing. When using a default profile, its slices as it should. I have not been able to find the process setting that is causing this. Can anyone clue me in? Tha...