Search found 76 matches

by sonra
Sun May 06, 2018 10:27 pm
Forum: Tech Support
Topic: crackes
Replies: 12
Views: 2336

Re: crackes

Hi guys the print that i sent the pic is a straight surface I tried to raising the extruder to 220 degrees cel. and use a 0.1 Primary Layer Height ( it was 0.15) . the prints look now much better Yes I use S3d ver 4 I attach the FFF file may be you can see some thing more i can change to make prints...
by sonra
Tue May 01, 2018 11:11 am
Forum: Tech Support
Topic: crackes
Replies: 12
Views: 2336

Re: crackes

Hi
Thanks for help I attach a pic
Doron
by sonra
Sat Apr 28, 2018 12:51 pm
Forum: Tech Support
Topic: crackes
Replies: 12
Views: 2336

crackes

Hi guys, I use M2 v4 printer and HatchBox PLA only I have a problem in printing mostly seen in middle and big prints that has cracks so the item easily can be broken My extruder temp is 210 cel. degrees and the heated bed is 6o degrees . I use MIC6 aluminum plate and PEI over it as bed surface Prima...
by sonra
Fri Mar 23, 2018 4:30 pm
Forum: Tech Support
Topic: MIC 6 plate and PEI
Replies: 3
Views: 1061

Re: MIC 6 plate and PEI

Thanks for help .The bed was not very leveled
Doron
by sonra
Wed Mar 21, 2018 7:55 pm
Forum: Tech Support
Topic: MIC 6 plate and PEI
Replies: 3
Views: 1061

MIC 6 plate and PEI

Hi guys
I try to print PLA on the MIC6 plate covered with PEI plate . till now with not great success ( the start print layer does not stick well ) .
To what temp. ( in C degrees ) do you heat the plate ?
Regards Doron
by sonra
Tue Mar 06, 2018 8:26 pm
Forum: General Discussion
Topic: filler for pla
Replies: 3
Views: 1303

Re: filler for pla

Thanks for your help
Doron
by sonra
Sun Mar 04, 2018 8:01 pm
Forum: General Discussion
Topic: filler for pla
Replies: 3
Views: 1303

filler for pla

Hi guys
After a print sometimes i use the dremel rotary tool to clean the support ( after I use the pliers ) and If i am careful the dremel remove to much
What do you advice to fill the damage? ( I print only PLA )
Regards Doron
by sonra
Sat Feb 10, 2018 12:11 am
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 33627

Re: BLTouch Auto Leveling Sensor

I am using the BLTOUCH . Do i have to adjust the Z offset number only when I try to print and if the print is not OK or there is other way to do it ?
I mean can I enter as default -1.55 and adjust it according print results or is any way to do it ?
by sonra
Fri Feb 09, 2018 2:12 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 33627

Re: BLTouch Auto Leveling Sensor

Hi May be i don't understand what I suppose to happen but i try to describe what i see 1) I sent a M280 P0 S10 command to drop the tip down . the tip is about 2 mm below the extruder 2) I send M851 with Z negative number 3) I recive a message "echo:Z Offset ok" 2) I send a G28 command The bed hit th...
by sonra
Thu Feb 08, 2018 8:16 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 33627

Z PROBE_OFFSET_FROM EXTRUDER

Hi , I have the M2 with v4 extruder ,use Samplify as control software . I installed the BLTouch sensor and one of my of setting I am not sure about is the Z PROBE_OFFSET_FROM EXTRUDER in the configuration.h ,what is the best way to define it and how it change or not the setting of Globel G code Offs...