Search found 83 matches

by sonra
Fri Mar 23, 2018 4:30 pm
Forum: Tech Support
Topic: MIC 6 plate and PEI
Replies: 3
Views: 1378

Re: MIC 6 plate and PEI

Thanks for help .The bed was not very leveled
Doron
by sonra
Wed Mar 21, 2018 7:55 pm
Forum: Tech Support
Topic: MIC 6 plate and PEI
Replies: 3
Views: 1378

MIC 6 plate and PEI

Hi guys
I try to print PLA on the MIC6 plate covered with PEI plate . till now with not great success ( the start print layer does not stick well ) .
To what temp. ( in C degrees ) do you heat the plate ?
Regards Doron
by sonra
Tue Mar 06, 2018 8:26 pm
Forum: General Discussion
Topic: filler for pla
Replies: 3
Views: 1694

Re: filler for pla

Thanks for your help
Doron
by sonra
Sun Mar 04, 2018 8:01 pm
Forum: General Discussion
Topic: filler for pla
Replies: 3
Views: 1694

filler for pla

Hi guys
After a print sometimes i use the dremel rotary tool to clean the support ( after I use the pliers ) and If i am careful the dremel remove to much
What do you advice to fill the damage? ( I print only PLA )
Regards Doron
by sonra
Sat Feb 10, 2018 12:11 am
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Re: BLTouch Auto Leveling Sensor

I am using the BLTOUCH . Do i have to adjust the Z offset number only when I try to print and if the print is not OK or there is other way to do it ?
I mean can I enter as default -1.55 and adjust it according print results or is any way to do it ?
by sonra
Fri Feb 09, 2018 2:12 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Re: BLTouch Auto Leveling Sensor

Hi May be i don't understand what I suppose to happen but i try to describe what i see 1) I sent a M280 P0 S10 command to drop the tip down . the tip is about 2 mm below the extruder 2) I send M851 with Z negative number 3) I recive a message "echo:Z Offset ok" 2) I send a G28 command The bed hit th...
by sonra
Thu Feb 08, 2018 8:16 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Z PROBE_OFFSET_FROM EXTRUDER

Hi , I have the M2 with v4 extruder ,use Samplify as control software . I installed the BLTouch sensor and one of my of setting I am not sure about is the Z PROBE_OFFSET_FROM EXTRUDER in the configuration.h ,what is the best way to define it and how it change or not the setting of Globel G code Offs...
by sonra
Sat Feb 03, 2018 12:41 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Re: BLTouch Auto Leveling Sensor

Hi
I found the problem .The sensor tip when in push position ( down ) was a little above the extruder , so the table when try to go to home position crushed into the extruder and not the sensor . Now i put spacer so the sensor tip is below the extruder and G28 and G29 do the job
by sonra
Fri Feb 02, 2018 4:43 pm
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Re: BLTouch Auto Leveling Sensor

Hi guys The sensor response to manual commands M280 P0 S10 ; pushes the pin down M280 P0 S90 ; pulls the pin up M280 P0 S120 ; Self test –keeps going until you do pin up/down or release alarm M280 P0 S160 ; Release alarm send M500 to store in EEPROM and m502 when i send G28 . The bed move x and y ho...
by sonra
Wed Jan 31, 2018 12:57 am
Forum: Modifications
Topic: BLTouch Auto Leveling Sensor
Replies: 60
Views: 38451

Re: BLTouch Auto Leveling Sensor

THANKS