Search found 22 matches

by daveb
Thu Jun 29, 2017 6:53 pm
Forum: Modifications
Topic: My overboard Enclosure
Replies: 2
Views: 1806

My overboard Enclosure

Here's what I'm working on. Wanted a cabinet I could also put my vinyl cutter in (that will be a lower section). it's an old entertainment cabinet I picked up at a Habitat store for around $45. The compartment on the upper right is for filament, slide out bottom shelf for 6 rolls, top I'm going to h...
by daveb
Thu Jun 29, 2017 6:49 pm
Forum: Modifications
Topic: Enclosure for the M2? Retain heat and contain smell...
Replies: 25
Views: 17258

Re: Enclosure for the M2? Retain heat and contain smell...

Here's one I'm working on. Wanted a cabinet I could also put my vinyl cutter in (that will be a lower section). it's an old entertainment cabinet I picked up at a Habitat store for around $45. The compartment on the upper right is for filament, slide out bottom shelf for 6 rolls, top I'm going to ha...
by daveb
Tue Jun 06, 2017 3:16 am
Forum: M2 Dual Extruder
Topic: Which Firmware for this??
Replies: 1
Views: 1831

Which Firmware for this??

Haven't used my printer since having to replace the Rambo board. When I did, I also added the Dual upgrade, and bottom Z-Stop and I have the Silver (older style) z-stop motor. . Bit confused on which firmware I should be using. I see a firmware for a system upgraded with 4 point leveling and z-stop ...
by daveb
Wed Mar 22, 2017 1:25 am
Forum: General Discussion
Topic: Enclosure Exhaust/Intake Fan Filter?
Replies: 1
Views: 1605

Enclosure Exhaust/Intake Fan Filter?

Filter for exhaust (or intake) fan? Anyone using a filter, with an enclosure, on the exhaust air, or intake air? Was looking at different filter options and ran across a small, about 1.5 inches thick, car filter clearanced for $4, Anyone think one of these would work? Thinking it may be a bit restri...
by daveb
Tue Mar 14, 2017 2:34 am
Forum: Modifications
Topic: MIC6 preorder number 3 *back for sale*
Replies: 70
Views: 34536

Re: MIC6 preorder number 3 *back for sale*

Do I need to set my bed heat higher, or just give it more time to heat up?
by daveb
Fri Jan 20, 2017 4:47 am
Forum: Tech Support
Topic: relocating Rambo board?
Replies: 1
Views: 1239

relocating Rambo board?

Anyone relocated the Rambo board outside the printer base? Had to replace my Rambo board and building an enclosure, thinking I could add wire and relocate it outside the enclosure. Anyone think of any concerns issue this would cause?
by daveb
Wed Jan 04, 2017 3:59 am
Forum: Tech Support
Topic: Nee help again trouble shooting, will not connect
Replies: 1
Views: 812

Nee help again trouble shooting, will not connect

If this is double I'll delete, thought I sent from phone. Setup a print before bed one night. Checked early morning and the nozzle was broken off hanging. May have been me zeroing. had ordered the parts to upgrade to RevE, It had blown fuse so I ordered some and all was well. Took it offline to upgr...
by daveb
Thu Dec 22, 2016 2:58 am
Forum: Modifications
Topic: MIC6 preorder number 3 *back for sale*
Replies: 70
Views: 34536

Re: MIC6 preorder number 3

I'll take one
by daveb
Sun Dec 04, 2016 10:45 pm
Forum: Modifications
Topic: Spider Conversion (from 3 to 4 Point Leveling)
Replies: 14
Views: 6759

Re: Spider Conversion (from 3 to 4 Point Leveling)

Couldn't you use blind rivet nuts for this?
by daveb
Tue Aug 09, 2016 5:30 pm
Forum: Tech Support
Topic: Need help to figure this out, before giving up
Replies: 7
Views: 1886

Re: Need help to figure this out, before giving up

I did use supports. Just removed them before the photos. The one with "the arms sticking out" (didn't noticed that it looked like that until mention I see that now Ha Ha), was a button also.