Search found 53 matches

by morganfree
Fri Dec 29, 2017 3:37 pm
Forum: Tech Support
Topic: Print stops at certain point
Replies: 19
Views: 9275

Re: Print stops at certain point

Hello Jk! Actually, I'm not getting any diagnostics/errors sine I'm printing from SD card and I don't have a display yet. So, I really don't know whats going on. I could start a print via usb in order to get that diagnostic. Anyway I'm getting the idea that it's something related to the extruder tem...
by morganfree
Sun Dec 24, 2017 9:20 pm
Forum: Tech Support
Topic: Print stops at certain point
Replies: 19
Views: 9275

Re: Print stops at certain point

Anyway Ed, the other question would be... Why this sudenly might started? 2-3 days ago I wasn't having an issue like this. Should be something related to the thermal sensor or the wire on the bed? I'm checking those but I can't seem to find any issue with them (I move and pull them in order to detec...
by morganfree
Sun Dec 24, 2017 9:07 pm
Forum: Tech Support
Topic: Print stops at certain point
Replies: 19
Views: 9275

Re: Print stops at certain point

Thanks Ed. I'm modifying the values on my firmware... Anyway I don't have all those variables you've mentioned. I only have these ones: #ifdef BED_LIMIT_SWITCHING #define BED_HYSTERESIS 6 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS #endif #define B...
by morganfree
Sat Dec 23, 2017 11:27 pm
Forum: Tech Support
Topic: Print stops at certain point
Replies: 19
Views: 9275

Print stops at certain point

I have an issue that it's causing me headaches! I've been printing PETG parts with success until a few days ago. It seems that the program is stopped after a couple of hours of printing and apparently "stops" completely, because when I reach the printer, the nozzle is stucked in the part... nozzle c...
by morganfree
Mon Nov 27, 2017 10:51 am
Forum: Tech Support
Topic: Table falling down in a middle of a print
Replies: 9
Views: 4431

Re: Table falling down in a middle of a print

@Ed, thanks a lot for your explanation!

I'll follow your links and contact MG support in order to make this upgrade immediatelly. Thank you very much again!
by morganfree
Sat Nov 25, 2017 5:52 pm
Forum: Tech Support
Topic: Table falling down in a middle of a print
Replies: 9
Views: 4431

Re: Table falling down in a middle of a print

Amazing! Both of you! Thanks a lot! Well, I wasn't that worried since I'm still printing, and as I said, it seems to be something that happens rarely. @Ednisley, I do have an old Z motor (black-silver) so I guess that should be one problem, even though I'm printing parts that I already printed, MANY...
by morganfree
Thu Nov 23, 2017 5:19 pm
Forum: Tech Support
Topic: Table falling down in a middle of a print
Replies: 9
Views: 4431

Table falling down in a middle of a print

Hello to all! Well, I had this issue two or three times already... The table is falling down (-Z) in a middle of a print, but the print continues... therefore the nozzle continues delivering plastic to the air... the table completely down, forming a nest of plastic above the table. I couldn't see if...
by morganfree
Wed Oct 11, 2017 8:03 pm
Forum: Tech Support
Topic: VIKI2 LCD installation
Replies: 5
Views: 5061

Re: VIKI2 LCD installation

Great! Let me find out how to deliver it to Brazil. I'll PM you once I find out. Thanks a lot!
by morganfree
Tue Oct 10, 2017 1:29 pm
Forum: Tech Support
Topic: VIKI2 LCD installation
Replies: 5
Views: 5061

Re: VIKI2 LCD installation

Or, buy a Viki1 from me ;) hahahaha I guess that I'm reading that phrase from you since 2013 !!! hahahaha I thought that during these last 4 years someone could actually install one of those! I don't know what will I do with that beautiful Viki2! I guess they focused on beauty but not on compatibil...
by morganfree
Mon Oct 09, 2017 1:50 pm
Forum: Tech Support
Topic: VIKI2 LCD installation
Replies: 5
Views: 5061

VIKI2 LCD installation

Hello, good morning! This is an old subject and for what I could read, maybe unresolved? It happens that I bought an VIKI2 and after that I read that it might be uncompatible with my M2!!!! Anyway, now I'm fighting to install it: I was folowing the instructions from VIKI itself and from your Wiki, b...