Search found 483 matches
- Sat Jan 16, 2021 4:50 am
- Forum: Tech Support
- Topic: Resonances in X & Y Axis?
- Replies: 5
- Views: 685
Re: Resonances in X & Y Axis?
could be the model was exported with too much detail, also check your M503 output .. jerk could have gotten accidently hosed, I know I had a similar issues when I had a fat finger entry..
- Sat Jan 09, 2021 5:57 pm
- Forum: M3-ID
- Topic: pause reload and continue
- Replies: 2
- Views: 725
Re: pause reload and continue
If you are doing this because you are about to run out and just want to keep going with a fresh roll of the same stuff you can do the following. When you have about a foot of the old left to go, hang you new roll, pull the remaining filament out of the Bowden tube, slide in your new filament, then c...
- Sat Jan 09, 2021 12:10 am
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
The more I use PS the less I feel like using PS..
- Fri Jan 08, 2021 5:05 am
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
Ah I see.. As to the length of time.. there are a lot of speed settings and the don't all default to a percentage of the over all speed.. so you have to mess with them all. And you have to decide if you want to enter actual speed values or % or one of the many speed settings.. Not that this is a bad...
- Thu Jan 07, 2021 11:42 pm
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
What is the variable layer process.. is that something that can be configured or just integral to the slicer? I can not find anything in any of the tabs that sounds like that.
- Thu Jan 07, 2021 4:50 pm
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
Yup! I still keep going back to the Devil I know..
- Thu Jan 07, 2021 4:59 am
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
one thing to take note, which I have recently discovered when parts were not the proper size. If you use a set extrusion width you have to set that in all the places or it will use auto if set to 0 That is under print settings advanced.. 8 fields need to be set.. for example if you want to use .4 fo...
- Sun Jan 03, 2021 3:03 pm
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
The Z offset on mine is adjusted by me with every layer height change, bed temp change (40C and 110C are not the same) and hot end change.. 10 - 12 is all good, it keeps the bed below the nozzle. when I put on the fiberglass plate it gets changed to 9.xxxx as that bed is a 1/4" thick. printing a sq...
- Sun Jan 03, 2021 4:55 am
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
The Z offset on mine is adjusted by me with every layer height change, bed temp change (40C and 110C are not the same) and hot end change.. 10 - 12 is all good, it keeps the bed below the nozzle. when I put on the fiberglass plate it gets changed to 9.xxxx as that bed is a 1/4" thick. printing a squ...
- Sat Jan 02, 2021 4:38 pm
- Forum: Software
- Topic: Prusaslicer 2.x
- Replies: 50
- Views: 5227
Re: Prusaslicer 2.x
Not sure on the Gcode, have not really taken time to learn it. If I recall I got this off the prusa forum or maybe one of the other profiles.. I forget. I do like the way the PS works. Printed some TPU rollers for a Total Gym yesterday and the outside surface is way nicer than anything S3D has been ...