Search found 594 matches
- Wed Sep 12, 2018 6:18 pm
- Forum: Filament
- Topic: Expiration Date on Filament?
- Replies: 8
- Views: 25331
Re: Expiration Date on Filament?
Thanks, I had kind of figured that to be the case ..But to tell the truth, I have not googled the question yet. Since the stuff we not really vacuum sealed I did't think it was hydroscopic but probably should goggle it now
- Wed Sep 12, 2018 4:32 pm
- Forum: Filament
- Topic: Expiration Date on Filament?
- Replies: 8
- Views: 25331
Re: Expiration Date on Filament?
Ninjaflex needs to be dried, is that correct? I did not do that prior to first use.. How bad does is suck up moisture.. PLA like or Nylon like??
- Wed Sep 12, 2018 3:31 am
- Forum: General Discussion
- Topic: M2 Rev F vs Rev E Differences?
- Replies: 3
- Views: 6523
Re: M2 Rev F vs Rev E Differences?
With a Feb 2018 M2 I would like to know as well ..
- Mon Sep 10, 2018 1:32 pm
- Forum: Modifications
- Topic: M2 x/y stepper isolation dampers NinjaFlex!
- Replies: 5
- Views: 7945
- Sun Sep 09, 2018 7:12 pm
- Forum: Modifications
- Topic: M2 x/y stepper isolation dampers NinjaFlex!
- Replies: 5
- Views: 7945
Re: M2 x/y stepper isolation dampers NinjaFlex!
They look to be the same size! If you have not used NinjaFlex, it is a little temperamental.. This was my first use of it and I had to rig a gravity feed for the spool. It is kind of a must as it does not feed well so pulling it up didn't work well at all. Also .5 nozzle and really slow.. 10mmS.. I ...
- Sun Sep 09, 2018 12:31 am
- Forum: Modifications
- Topic: M2 x/y stepper isolation dampers NinjaFlex!
- Replies: 5
- Views: 7945
M2 x/y stepper isolation dampers NinjaFlex!
I have no idea on longevity but these work great without the Twist offset of the shaft that you get with the pre-made steal dampers that only use 2 screws to anchor to the frame. Not Dead silent but close! I saw the STL on Thingivers and the person who had made them had a drawing with measurement so...
- Fri Sep 07, 2018 7:03 pm
- Forum: M2 Dual Extruder
- Topic: M2 REV.F w/Dual Extrusion Prep Help
- Replies: 4
- Views: 18011
Re: M2 REV.F w/Dual Extrusion Prep Help
That is simple S3D is the manufactures (MakerGear) recommended software. S3D is a supported paid product S3D is only $150 and at this point and does not have a recurring support cost. S3D will be releasing an update in the near future so you will have the latest and greatest. Good luck with the Bean...
- Thu Sep 06, 2018 10:00 pm
- Forum: Filament
- Topic: Need Flexible Filament advice
- Replies: 11
- Views: 41922
Re: Need Flexible Filament advice
6mmS .. Ok, had it running at 8 and it seemed to work better a bit faster. Just finished a spool center for the little slash spool to put it on a dowel above the printer.. Also, the NinjaFlex dampers work fairly well, not as good as a real damper for noise, but a good amount of noise reduction "with...
- Thu Sep 06, 2018 8:16 pm
- Forum: M2 Dual Extruder
- Topic: M2 REV.F w/Dual Extrusion Prep Help
- Replies: 4
- Views: 18011
Re: M2 REV.F w/Dual Extrusion Prep Help
Simplified 3D is the recommended slicing software which will let you do all of that I believe. I do not have the dual so sit tight the gurus stop by later in the evening every day or so.
- Thu Sep 06, 2018 8:10 pm
- Forum: How-to/Guides/Tips
- Topic: can I use glass plate with Kapton tape down?
- Replies: 5
- Views: 11378
Re: can I use glass plate with Kapton tape down?
just put the hair spray or glue stick on the tape.. Washes off just the same.
I would assume the only reason you are using hair spray or glue stick is to get the part off the tape, as I have found nothing that won't stick to it.. EPA, PETG all sticks like it was dipped in CA adhesive.
I would assume the only reason you are using hair spray or glue stick is to get the part off the tape, as I have found nothing that won't stick to it.. EPA, PETG all sticks like it was dipped in CA adhesive.