Search found 79 matches
- Sat Jan 30, 2016 7:05 pm
- Forum: Tech Support
- Topic: Crack in extruder motor holder
- Replies: 4
- Views: 5161
Re: Crack in extruder motor holder
Mine did that too after accidentally colliding with one of the binder clips. I used a couple of zip ties to cinch it down so I could print a new one, but you have to really pull them tight with pliers. It worked long enough to print two new mounts and was still tight when I replaced it.
- Thu Jan 14, 2016 4:28 am
- Forum: General Discussion
- Topic: Santa Just Visited
- Replies: 22
- Views: 21604
Re: Santa Just Visited
I am SO jealous! I have been looking for a way to cost-justify getting another (or multiple) printers but so far, it is elusive. I hope to join the "multiple" club soon…
In the meantime, I guess I can live vicariously!
In the meantime, I guess I can live vicariously!
- Fri Jan 08, 2016 5:39 am
- Forum: Tech Support
- Topic: Is my RAMBo dead?
- Replies: 7
- Views: 9156
Re: Is my RAMBo dead?
At least now I'll know where to look if it acts up again.
And I meant Jim, not Insta! All you multi-machine guys blur after a while when seen through jealous eyes
And I meant Jim, not Insta! All you multi-machine guys blur after a while when seen through jealous eyes
- Fri Jan 08, 2016 5:25 am
- Forum: Tech Support
- Topic: Is my RAMBo dead?
- Replies: 7
- Views: 9156
Re: Is my RAMBo dead?
So, the mystery deepens. I did as Insta suggested and unplugged the Z motor. I was then able to jog X and Y, and when I jogged Z, nothing happened (of course with the motor unplugged). I was able to continue jogging the X and Y. I plugged the Z motor back in and before messing with the firmware agai...
- Thu Jan 07, 2016 4:39 am
- Forum: Tech Support
- Topic: Is my RAMBo dead?
- Replies: 7
- Views: 9156
Is my RAMBo dead?
Last night my printer was working perfectly in the Quick Start app for the new leveling system and I had done the setup multiple times with no issues. I haven't actually printed anything since doing the conversion last week. Tonight I go to fire it up, and anything involving a Z jog input or home al...
- Sun Dec 27, 2015 1:27 am
- Forum: Tech Support
- Topic: Unsure what is causing this print problem
- Replies: 14
- Views: 14307
Re: Unsure what is causing this print problem
Speaking of which, I've noticed that the build platform seems to lose its level rather quicker than I expected. I've noticed that after a few hours of print time if I check the level, it is no longer true. I don't really know what the acceptable amount of unevenness is yet, but the bed is noticeabl...
- Mon Dec 21, 2015 7:16 pm
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 232880
Re: Testers Needed
I just realized that the Quick Start App might be considered as part of the new system, so I hope posting screen shots of some of the pages didn't go against Rick's "no photos" request. I assumed that only applied to the hardware. If not, I will delete them or an admin can do so. Jim, I'm also runni...
- Mon Dec 21, 2015 2:15 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 232880
Re: Testers Needed
I should clarify it's jumbled and also cut off in some instances.
- Mon Dec 21, 2015 1:58 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 232880
Re: Testers Needed
I have some observations and a question about S3D. Overall the upgrade was painless and the bed is SO MUCH easier to level. It takes all the mental gymnastics out of it. The hardware installation went smooth and the instructions were very clear. The only trouble I had was when attaching the spider t...
- Thu Dec 10, 2015 1:29 am
- Forum: Modifications
- Topic: E3D V6
- Replies: 199
- Views: 243471
Re: E3D V6
It's been a while since I installed an E3D, but I seem to remember having the instructions say to bring it up to full operating temperature and then tighten the nozzle a bit more. I've never had a leak. Also, you mentioned you were part way through a print and the printer dinged that it was done - i...