Search found 116 matches
- Sun May 06, 2018 10:27 pm
- Forum: Tech Support
- Topic: crackes
- Replies: 12
- Views: 13770
Re: crackes
Hi guys the print that i sent the pic is a straight surface I tried to raising the extruder to 220 degrees cel. and use a 0.1 Primary Layer Height ( it was 0.15) . the prints look now much better Yes I use S3d ver 4 I attach the FFF file may be you can see some thing more i can change to make prints...
- Tue May 01, 2018 11:11 am
- Forum: Tech Support
- Topic: crackes
- Replies: 12
- Views: 13770
Re: crackes
Hi
Thanks for help I attach a pic
Doron
Thanks for help I attach a pic
Doron
- Sat Apr 28, 2018 12:51 pm
- Forum: Tech Support
- Topic: crackes
- Replies: 12
- Views: 13770
crackes
Hi guys, I use M2 v4 printer and HatchBox PLA only I have a problem in printing mostly seen in middle and big prints that has cracks so the item easily can be broken My extruder temp is 210 cel. degrees and the heated bed is 6o degrees . I use MIC6 aluminum plate and PEI over it as bed surface Prima...
- Fri Mar 23, 2018 4:30 pm
- Forum: Tech Support
- Topic: MIC 6 plate and PEI
- Replies: 3
- Views: 5148
Re: MIC 6 plate and PEI
Thanks for help .The bed was not very leveled
Doron
Doron
- Wed Mar 21, 2018 7:55 pm
- Forum: Tech Support
- Topic: MIC 6 plate and PEI
- Replies: 3
- Views: 5148
MIC 6 plate and PEI
Hi guys
I try to print PLA on the MIC6 plate covered with PEI plate . till now with not great success ( the start print layer does not stick well ) .
To what temp. ( in C degrees ) do you heat the plate ?
Regards Doron
I try to print PLA on the MIC6 plate covered with PEI plate . till now with not great success ( the start print layer does not stick well ) .
To what temp. ( in C degrees ) do you heat the plate ?
Regards Doron
- Tue Mar 06, 2018 8:26 pm
- Forum: General Discussion
- Topic: filler for pla
- Replies: 3
- Views: 6771
Re: filler for pla
Thanks for your help
Doron
Doron
- Sun Mar 04, 2018 8:01 pm
- Forum: General Discussion
- Topic: filler for pla
- Replies: 3
- Views: 6771
filler for pla
Hi guys
After a print sometimes i use the dremel rotary tool to clean the support ( after I use the pliers ) and If i am careful the dremel remove to much
What do you advice to fill the damage? ( I print only PLA )
Regards Doron
After a print sometimes i use the dremel rotary tool to clean the support ( after I use the pliers ) and If i am careful the dremel remove to much
What do you advice to fill the damage? ( I print only PLA )
Regards Doron
- Sat Feb 10, 2018 12:11 am
- Forum: Modifications
- Topic: BLTouch Auto Leveling Sensor
- Replies: 63
- Views: 232795
Re: BLTouch Auto Leveling Sensor
I am using the BLTOUCH . Do i have to adjust the Z offset number only when I try to print and if the print is not OK or there is other way to do it ?
I mean can I enter as default -1.55 and adjust it according print results or is any way to do it ?
I mean can I enter as default -1.55 and adjust it according print results or is any way to do it ?
- Fri Feb 09, 2018 2:12 pm
- Forum: Modifications
- Topic: BLTouch Auto Leveling Sensor
- Replies: 63
- Views: 232795
Re: BLTouch Auto Leveling Sensor
Hi May be i don't understand what I suppose to happen but i try to describe what i see 1) I sent a M280 P0 S10 command to drop the tip down . the tip is about 2 mm below the extruder 2) I send M851 with Z negative number 3) I recive a message "echo:Z Offset ok" 2) I send a G28 command The bed hit th...
- Thu Feb 08, 2018 8:16 pm
- Forum: Modifications
- Topic: BLTouch Auto Leveling Sensor
- Replies: 63
- Views: 232795
Z PROBE_OFFSET_FROM EXTRUDER
Hi , I have the M2 with v4 extruder ,use Samplify as control software . I installed the BLTouch sensor and one of my of setting I am not sure about is the Z PROBE_OFFSET_FROM EXTRUDER in the configuration.h ,what is the best way to define it and how it change or not the setting of Globel G code Offs...