Hi guys
It was a problem of leveling ans Z endstop .Thanks for help
Search found 116 matches
- Tue Dec 01, 2015 5:40 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
- Mon Nov 30, 2015 8:08 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
Re: problem in printing
I did use any other material then PLA the screw are OK . I try to print with a new PLA roll that I take out from pack and has a anti humidity material little beg in and get the some result as you can see in picture some of print is nice and some is like points
- Sun Nov 29, 2015 10:58 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
Re: problem in printing
I tried to release a bit the tension
Print in 190 degrees Cel. and 210 with no different in results
Print in 190 degrees Cel. and 210 with no different in results
- Sun Nov 29, 2015 10:26 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
Re: problem in printing
Hi
I looked at the extruder motor and attach a pic I clean the teeth but there is not melt bit of filament . How do I know if tension is proper ?
\
I looked at the extruder motor and attach a pic I clean the teeth but there is not melt bit of filament . How do I know if tension is proper ?
\
- Sun Nov 29, 2015 1:43 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
Re: problem in printing
20151129_144119.jpg Hi Thanks for try to help . I slow down speed but with no change in print outcome , checked the screws of the x y axis motors but they are no loose , checked the wires to motors and they seems to be OK . Try to print a simple open box but the print to my opinion seems to be good...
- Sat Nov 28, 2015 5:03 pm
- Forum: Tech Support
- Topic: problem in printing
- Replies: 12
- Views: 12197
problem in printing
Hi all , I use the M2 with Simplify3D software for some time Today I start get bad prints so i go back to demo file that comes with printer and there is a problem in print as you can see in pictures below . I try two PLA from different manufacturers but get the some result > can any one help Regards...
- Thu Oct 29, 2015 6:07 pm
- Forum: Tech Support
- Topic: Glass plate breaked
- Replies: 2
- Views: 3670
Re: Glass plate breaked
Hi
Thanks for help
Thanks for help
- Wed Oct 28, 2015 6:03 pm
- Forum: Tech Support
- Topic: Glass plate breaked
- Replies: 2
- Views: 3670
Glass plate breaked
Hi guys ,
I succeed to break the plate , I wonder if I can replace it with simple glass plate I order from glazier or it is in any way special . Is it better to stick with glass or replace it with other material plate like aluminum ???
Regards Doron
I succeed to break the plate , I wonder if I can replace it with simple glass plate I order from glazier or it is in any way special . Is it better to stick with glass or replace it with other material plate like aluminum ???
Regards Doron
- Sat Sep 12, 2015 9:41 pm
- Forum: Getting Started
- Topic: problem during few hours project
- Replies: 2
- Views: 4808
Re: problem during few hours project
Hi
Thanks . Will give at try
'
Thanks . Will give at try
'
- Sat Sep 12, 2015 6:30 pm
- Forum: Getting Started
- Topic: end of filament in middle of print
- Replies: 4
- Views: 6705
Re: end of filament in middle of print
Thanks for help . I wish next printers will have sensor that stop the print in case filament is ended in middle of print ( to my knowledge in electronic it is not very big problem )