Search found 76 matches
- Sat Apr 23, 2016 12:16 am
- Forum: M2 Dual Extruder
- Topic: Dual Ready?
- Replies: 23
- Views: 32288
Re: Dual Ready?
I used profiles that Jules posted with some slight differences. Yes to the ooze shield.
- Thu Apr 21, 2016 4:35 am
- Forum: M2 Dual Extruder
- Topic: Dual Ready?
- Replies: 23
- Views: 32288
Re: Dual Ready?
I just wanted to make a quick post in response to this question. I purchased a dual kit nearly a year ago. I had reservations about all the problems it would cause so I didn't install it until a few days ago. I am by no means an expert and couldn't have made the progress I have without the help of t...
- Sun Apr 17, 2016 7:47 am
- Forum: M2 Dual Extruder
- Topic: Tool Change Scripts
- Replies: 1
- Views: 4010
Tool Change Scripts
I have made some progress dialing in my dual. The ooze thing is the killer. I have read that tool change scripts can be beneficial by reducing the temp of the extruder not currently in use. Anyone want to share their scripts? I have seen reference to some here and there but thought it might be nice ...
- Sun Apr 17, 2016 4:08 am
- Forum: M2 Dual Extruder
- Topic: Upgrade
- Replies: 3
- Views: 5501
Re: Upgrade
Next issue.... The display grid in Simplify3D is smaller than the build plate. I figured this is due to the the reduced travel distance of Tool 1. When I goto print something that goes to the edges of the grid to check level it ends up printing off of the table. I am using the default profile from S...
- Sat Apr 16, 2016 11:40 pm
- Forum: M2 Dual Extruder
- Topic: Upgrade
- Replies: 3
- Views: 5501
Upgrade
After a year of debating I finally upgraded my M2. Everything went smooth and I have set the z distance and leveled the bed. I printed the the calibration stl and noticed when x homed it was off the plate. I also notice both extruders were heating up. Ultimately it printed and measured out near perf...
- Mon Apr 11, 2016 12:24 am
- Forum: M2 Dual Extruder
- Topic: Dual Advice - Sample Prints
- Replies: 6
- Views: 8423
Re: Dual Advice - Sample Prints
Did you find the directions accurate?
- Sun Apr 10, 2016 11:09 pm
- Forum: M2 Dual Extruder
- Topic: Dual Advice - Sample Prints
- Replies: 6
- Views: 8423
Re: Dual Advice - Sample Prints
Thanks for the replies! It seems as though it is time to try it out. I will read the installation guide and get my head wrapped around it. How long did it take to swap out the parts and get the firmware updated?
Thanks
Thanks
- Sun Apr 10, 2016 4:30 pm
- Forum: M2 Dual Extruder
- Topic: Dual Advice - Sample Prints
- Replies: 6
- Views: 8423
Dual Advice - Sample Prints
I purchased the dual upgrade months ago but have never installed it. The postings I have seen here and various places on the internet made me reluctant to try. I have gotten to a point with the single that my print usually come out good but am tempted to do the upgrade. So I have a few questions; 1....
- Sat May 09, 2015 2:06 pm
- Forum: M2 Dual Extruder
- Topic: Sample Prints - Dual Feedback
- Replies: 3
- Views: 6460
Re: Sample Prints - Dual Feedback
Thanks for the info.
- Sat May 09, 2015 3:14 am
- Forum: M2 Dual Extruder
- Topic: Sample Prints - Dual Feedback
- Replies: 3
- Views: 6460
Sample Prints - Dual Feedback
I went ahead and purchased the V4 Dual awhile back. The kit arrived recently but I haven't installed it yet. Looking around this forum there hasn't been a lot of discussion about the Dual recently. I am not sure why but was hoping to hear some feedback as to how it prints. It would also be nice to s...