Search found 667 matches
- Wed Mar 30, 2016 3:05 pm
- Forum: General Discussion
- Topic: Anybody know what this is?
- Replies: 5
- Views: 7479
Re: Anybody know what this is?
Rubber coated fiber Glass insulation to cover the hot end.
- Wed Mar 30, 2016 12:36 pm
- Forum: Tech Support
- Topic: Inter-layer adhesion issue
- Replies: 48
- Views: 43018
Re: Inter-layer adhesion issue
Every picture points to and incorrectly set z height. You need to take an hour or more and set your printer up right. Get the bed level and z height correctly set . Print it at 190. If pla strings a lot you are too hot.slow your print speed down to 2400. This will help as well. Everything you are ex...
- Wed Mar 30, 2016 12:22 pm
- Forum: Tech Support
- Topic: V4 clogged nozzle - where can I find spares?
- Replies: 7
- Views: 8694
Re: V4 clogged nozzle - where can I find spares?
I just wonder how many of these clogs are just stripped filament. Are people getting failures to extrude and just pulling nozzles ? I think in all the years since the V4 released I have only had to unclog via blow torch once. And the only time you replace a nozzle is from extreme wear. Which does ha...
- Wed Mar 30, 2016 2:12 am
- Forum: Filament
- Topic: New Filament Announcement from Polymaker
- Replies: 6
- Views: 8051
Re: New Filament Announcement from Polymaker
Modify max temp in firmware. At.your own risk of course.
- Sun Mar 27, 2016 11:32 pm
- Forum: General Discussion
- Topic: Raspberry Pi 3
- Replies: 65
- Views: 86367
Re: Raspberry Pi 3
http://docstech.net/OctoPiMirror/nightly/ Grab the latest nightly . That is what I am running . It has been flawless.
- Sun Mar 27, 2016 12:56 am
- Forum: Modifications
- Topic: New Extruder Drive Gear
- Replies: 59
- Views: 75661
Re: New Extruder Drive Gear
I have not had the reason to print either of those ...although ninja flex looks appealing I just have not had the use scenario to order any. And I have.never heard of bridge nylon. My short experience with most nylon has been terribly warpy...new word !
- Sat Mar 26, 2016 12:15 pm
- Forum: Modifications
- Topic: New Extruder Drive Gear
- Replies: 59
- Views: 75661
Re: New Extruder Drive Gear
So far so good for me ...lol ...sorry Jim ;) It likes carbon fiber and petg so far. I have not tried it at any break neck speed yet to see if the smaller teeth are up to the challenge. What is the thinking behind this new gear ? I mostly only see easier filament loading . On a side note I like the s...
- Sat Mar 26, 2016 12:10 pm
- Forum: General Discussion
- Topic: They are breeding...
- Replies: 10
- Views: 13109
Re: They are breeding...
Drinking and printing in one area ??? Who knew ? who knew ? lol Nice setup !!
- Sat Mar 26, 2016 12:09 pm
- Forum: Filament
- Topic: Feed Failures with PETG
- Replies: 33
- Views: 38679
Re: Feed Failures with PETG
I'd think the only real fix is to re-spool filament to another good reel and at the same time have it running through a gauge that would trip the whole process to off if it hits an oversize spot in the filament. Kind of like when you buy bulk fishing line to fill your reel. Or just find another bra...
- Fri Mar 25, 2016 11:35 pm
- Forum: Filament
- Topic: Feed Failures with PETG
- Replies: 33
- Views: 38679
Re: Feed Failures with PETG
My roll failures are 100 percent definitely not my fault !!!! I handle all rolls the same ! Carefully ! When you cut 10 foot extrusion issues out of a roll that is inexcusable. Not the fault of loading and unloading incorrectly. And I have put new rolls on only to find 10 hrs in.... a crossed filame...