Search found 897 matches
- Tue Jun 19, 2018 2:33 pm
- Forum: Tech Support
- Topic: M2 nightmare with soft filiment
- Replies: 26
- Views: 29748
Re: M2 nightmare with soft filiment
I redesigned the stock drive to have a hinge and use springs for tension (see http://forum.makergear.com/viewtopic.php?f=10&t=3283) and I never have to adjust tension when switching between any filaments anymore. I've never run EPA but I don't have any problems running flex stuff.... like mentioned ...
- Tue May 22, 2018 3:43 am
- Forum: Tech Support
- Topic: Extrude stops extruding (not jammed), consistent temp issues (m2)
- Replies: 7
- Views: 8273
Re: Extrude stops extruding (not jammed), consistent temp issues (m2)
3a. If the platform thermistor cable shows no problem, then you need a new platform thermistor. I don't know if they're available separately or if you're in for a whole new assembly. You can get these separate you just have to ask for them as they are not listed on the site. (they were about $15 la...
- Mon May 21, 2018 12:20 am
- Forum: Filament
- Topic: PETG your favorite brand?
- Replies: 17
- Views: 45689
Re: PETG your favorite brand?
I use eSUN PETG and it works awesome. There is an entire thread on here too on what settings to use.
I usually get it on Amazon from INTSERVO but you can get it direct to https://www.intservo.com (Will is a great guy to deal with.)
I usually get it on Amazon from INTSERVO but you can get it direct to https://www.intservo.com (Will is a great guy to deal with.)
- Fri May 18, 2018 2:37 pm
- Forum: Tech Support
- Topic: M2 octoprint on Pi what to buy
- Replies: 21
- Views: 26454
Re: M2 octoprint on Pi what to buy
Almost perfect, got webcam hacked so I can focus it.. but can I put it inside my enclosure .. guess it will survive the heat if I print abs? gets over 100F where I will have it mounted.. any horror stories? I can put it out side but the plexi glass really sucks.. I'd be careful... I use cheap Logit...
- Sun May 13, 2018 4:21 pm
- Forum: Tech Support
- Topic: M2 octoprint on Pi what to buy
- Replies: 21
- Views: 26454
Re: M2 octoprint on Pi what to buy
Will using the pi as the interface while the print is running cause the printer to stop when the pi is busy with me using the UI? I guess I don't understand what your trying to do... Usually the whole point of using a Pi and Octoprint is to free up a main computer and just have a reliable system fe...
- Sun May 13, 2018 5:45 am
- Forum: General Discussion
- Topic: Setting in S3D to raise/lower bed on startup?
- Replies: 3
- Views: 6823
Re: Setting in S3D to raise/lower bed on startup?
If your talking about just adjusting the Z gap on a Rev E. printer without using the Makergear software. First Type M501 to read the EEPROM parameters Look for the M206 line. (it should look something like M206 X0.0 Y0.0 Z4.20) You can then adjust it using M206 Z[new value] (add to the number to mak...
- Sun May 13, 2018 5:36 am
- Forum: Tech Support
- Topic: M2 octoprint on Pi what to buy
- Replies: 21
- Views: 26454
Re: M2 octoprint on Pi what to buy
With octoprint you can do all that from any computer, table, or even your smart phone you don't need all that extra stuff.
- Fri May 11, 2018 8:55 pm
- Forum: Tech Support
- Topic: M2 octoprint on Pi what to buy
- Replies: 21
- Views: 26454
Re: M2 octoprint on Pi what to buy
So maybe I should ask.. can you monitor and control with one Pi? The ribbon cable kind of sucks for creative installations.. I don't really want the CPU mounted in my enclosure.. Will the Motioneye0S work with a USB webcam or just he PI camera module? You can monitor and control with Octoprint with...
- Thu May 10, 2018 2:39 pm
- Forum: Tech Support
- Topic: M2 printing off SD stops if USB port bounce
- Replies: 5
- Views: 6199
Re: M2 printing off SD stops if USB port bounce
I'm not sure why you would plug it back in while it's printing :? but yeah don't do that :D The only way a pi is going to "go down" is if you lose power and at that point your printer will too so you're SOL either way. The Pi setup with Octoprint is probably the best and most flawless why you can ru...
- Thu May 10, 2018 4:25 am
- Forum: Tech Support
- Topic: M2 printing off SD stops if USB port bounce
- Replies: 5
- Views: 6199
Re: M2 printing off SD stops if USB port bounce
You can start a print from S3D using the "Print from SD Card" button then just yank the USB cord out of the computer and the print will continue to print without any possible interruptions...
or better yet get a Raspberry Pi setup and run Octoprint and free up your computer all together.
or better yet get a Raspberry Pi setup and run Octoprint and free up your computer all together.