Search found 53 matches
- Sun Jun 29, 2014 7:47 pm
- Forum: Modifications
- Topic: E3D V6
- Replies: 199
- Views: 242966
Re: E3D V6
A better solution might be to ignore the E3D instructions on the v6 and connect the heating element with the wires going out the right side, opposite of the thermistor. Bring up all wires except for the thermistor up the right side of the hot end, and allow a bit of extra length on the wire! That's...
- Sat Jun 28, 2014 8:56 pm
- Forum: General Discussion
- Topic: Need some advice on how to respond
- Replies: 26
- Views: 32582
Re: Need some advice on how to respond
yet another person expecting a complicated device to work like a toaster.
anyway, i just submitted my 5 star review to be added to the rest.
anyway, i just submitted my 5 star review to be added to the rest.
- Sat Jun 28, 2014 8:12 pm
- Forum: General Discussion
- Topic: Need some advice on how to respond
- Replies: 26
- Views: 32582
Re: Need some advice on how to respond
The best thing I can think of is another campaign to get people who have purchased an M2 and like it to post a review on Amazon. You have over 1000 customers but only ~50 reviews. . . there must be more people out there who can be convinced to write you a good review. . I've been meaning to do that...
- Thu Jun 26, 2014 8:29 pm
- Forum: Tech Support
- Topic: Gaps near through-holes in ABS
- Replies: 8
- Views: 10069
Re: Gaps near through-holes in ABS
almost looks like your extrusion multiplier is too low for the configured extrusion width. what is the width set to?
- Thu Jun 26, 2014 7:56 pm
- Forum: Modifications
- Topic: E3D V6
- Replies: 199
- Views: 242966
Re: E3D V6
Cool thanks for the info Tim!
- Thu Jun 26, 2014 12:34 am
- Forum: Printed Object Showcase
- Topic: Big Red Beast. A 3D printed quadrotor
- Replies: 19
- Views: 23048
Re: Big Red Beast. A 3D printed quadrotor
nice work! i keep meaning to take some time and sit down to design a mini quad platform for my aeroquad flight controller. right now its in a big, sturdy airframe i rebuilt after i crashed my cyclone. its tough and the thing has a lot of lifting power, but its a bit intimidating to fly around and yo...
- Tue Jun 24, 2014 5:47 am
- Forum: Modifications
- Topic: E3D V6
- Replies: 199
- Views: 242966
Re: E3D V6
so i watched their introductory video and saw the mention of it. then i re-read their assembly instructions and there is zero mention of it.
well i suppose i will go take it off and assemble it the proper way. thanks!
edit: oh man, extrusion consistency is SO much better now. imagine that!
well i suppose i will go take it off and assemble it the proper way. thanks!
edit: oh man, extrusion consistency is SO much better now. imagine that!
- Tue Jun 24, 2014 3:55 am
- Forum: Modifications
- Topic: E3D V6
- Replies: 199
- Views: 242966
Re: E3D V6
so you're supposed to run that tube down into the hotend? the instructions don't mention it, nor do any videos i can find of assembling it. i've been printing makergear abs without it and it has jammed once or twice, but i believe that was due to me still needing to tweek my extrusion multiplier and...
- Tue Jun 24, 2014 3:09 am
- Forum: Printed Object Showcase
- Topic: Partial Success, Partial Massive Fail
- Replies: 4
- Views: 7630
Re: Partial Success, Partial Massive Fail
came out pretty darn good!
- Tue Jun 24, 2014 3:07 am
- Forum: M2 Dual Extruder
- Topic: Dual Extruder Upgrade - Limited Availability
- Replies: 163
- Views: 178533
Re: Dual Extruder Upgrade - Limited Availability
yeah so far all ive read about printing PC says that you pretty much need a heated bed chamber. i wonder if i just setup my heat gun to blow on it the whole time i can get away without having one. eh now that i think about it though, i don't really want a higher electric bill so i'll pass on that li...