Search found 594 matches
- Wed Oct 10, 2018 1:07 am
- Forum: Software
- Topic: M2 Quick Start Keeps Dropping Session with Printer
- Replies: 3
- Views: 17119
Re: M2 Quick Start Keeps Dropping Session with Printer
The most convenient way to set up your M2 is with octoprint on a raspberry pi. It will cost you about $100 and a little time to set it up but you will be able to access it from any computer in your network and you will not have any issues with stalled or stopping prints. SD card swapping gets to be ...
- Tue Oct 09, 2018 9:40 pm
- Forum: Tech Support
- Topic: Streaking on the surface finish of PETG print
- Replies: 12
- Views: 13417
Re: Streaking on the surface finish of PETG print
I see the same results on many of my prints.. Not sure if it can be fixed.. maybe more Zlift?
- Mon Oct 08, 2018 3:54 pm
- Forum: M2 Dual Extruder
- Topic: Stringy dual print
- Replies: 4
- Views: 22169
Re: Stringy dual print
Thanks Tim!
- Sun Oct 07, 2018 4:47 pm
- Forum: M2 Dual Extruder
- Topic: Stringy dual print
- Replies: 4
- Views: 22169
Re: Stringy dual print
@DrE What was the main reason to upgrade to duel on the M2, multi color or desolvable supports? The more parts I design the more I wish I could use supports in places that I can't remove them from.. @Tim, Your statement about temp, is it possible to have each extruder at a different temp or does it ...
- Sat Oct 06, 2018 12:33 am
- Forum: Tech Support
- Topic: Flex Filament Stops Feeding
- Replies: 2
- Views: 4799
Re: Flex Filament Stops Feeding
I had retraction off .. Will work on for sure before I actually need to print something.
Thanks!
Thanks!
- Fri Oct 05, 2018 1:46 pm
- Forum: M3-ID
- Topic: Printing with Ninjaflex?
- Replies: 29
- Views: 75778
Re: Printing with Ninjaflex?
Ok will give that a try when I have some time.
Have to wonder what changes were made in the filament drive housing between the M2 and M3..
Have to wonder what changes were made in the filament drive housing between the M2 and M3..
- Fri Oct 05, 2018 4:02 am
- Forum: M3-ID
- Topic: Printing with Ninjaflex?
- Replies: 29
- Views: 75778
Re: Printing with Ninjaflex?
Doesn't get wrapped around, it is bubbly in that there are areas where it stops feeding and has holes.. Not so much with the .5 nozzle but .35 I just could not get to work. letting the filament run through my fingers while printing, it feels like is stops at times.. This is being gravity fed from ab...
- Thu Oct 04, 2018 5:46 pm
- Forum: How-to/Guides/Tips
- Topic: Horizontal axis inaccurate - M3 SE
- Replies: 15
- Views: 39365
Re: Horizontal axis inaccurate - M3 SE
I have seen the sliding glass post and seen it in action on my own M2. I made plastic (imagine that with a 3d printer ) shims to install between the glass and rubber corners to keep it from moving without cranking down on the plastic hold downs.
- Thu Oct 04, 2018 7:59 am
- Forum: M3-ID
- Topic: Printing with Ninjaflex?
- Replies: 29
- Views: 75778
Re: Printing with Ninjaflex?
95% of my prints are in either Ninjaflex or Cheetah. I have a M2 with .5 nozzle for big stuff and an M3-ID with .35 nozzle for the smaller stuff. I even got dual color ninjaflex parts printing. How do you get the stuff to feed smoothly? M2 with a .5 I can get it to "Print" but is is not smooth and ...
- Thu Oct 04, 2018 12:18 am
- Forum: Tech Support
- Topic: Simplify 3d fff settings
- Replies: 9
- Views: 12493
Re: Simplify 3d fff settings
I never went there as every time I would ask people who had switched they would say that S3D was better in so many other ways..