Is there a listed max operating temperature for the M2 (dual setup) ?
I'm trying to determine if I'm running into a heat issue and want to measure it and compare to the max operating temp..
Thx!
Search found 195 matches
- Mon Jun 13, 2016 1:24 pm
- Forum: General Discussion
- Topic: Max operating temperature?
- Replies: 4
- Views: 5519
- Mon Jun 13, 2016 12:32 pm
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
I'll check that if this print fails. I had re-written the gcode yesterday using the latest version of S3D in case they changed/optimized something... I do notice that S3D hangs while it is writing the file to disk. Once it is complete, the UI becomes responsive...I wash thinking it was a threading i...
- Mon Jun 13, 2016 11:19 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
No, directly into UPS...previously into a powerstrip to the wall outlet
- Mon Jun 13, 2016 2:49 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
I always eject from the pc.... I'm not aware of a way to eject from the printer itself... I did check the SD for errors on the Windows computer and it didn't find any... I've rescliced the file in the latest version of S3D and used all its repair capabilities to ensure its not the file..and I'm runn...
- Mon Jun 13, 2016 1:26 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
Well I had the UPS in place for the last run and the print failed in 2hrs...and it wasn't connected to the computer..
I wish there was a log or some way of getting feedback to understand what is going on....
I wish there was a log or some way of getting feedback to understand what is going on....
- Mon Jun 13, 2016 12:52 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
Okay, I had a couple of things happen today.... I had a print that was working since last night but there was a power outage today and it killed the print..of course.. I went out and bought a UPS and hooked that up and started a new print...disconnected from the computer and I just went in and notic...
- Sun Jun 12, 2016 1:57 pm
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
You were correct..I have 3.1.0 on my machine installed, but I pin the launcher to my taskbar and when you install an update they never really upgrade, but install it side-by-side...So my taskbar launcher was launching the old version... So there is no way for me to know which was running when the pr...
- Sun Jun 12, 2016 1:22 pm
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
Hey Jim, I'm not sure I see the setting you are talking about...I've attached a screenshot...Maybe you meant Flow Control->Hardware Flow Control from the drop down? I'll also check for updates on my Windows machine....If this print completes,however, I'll likely just pull the USB cable for long prin...
- Sun Jun 12, 2016 3:44 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
Okay I'm impatient...
I restarted the print...I waited for it to start and then pulled the USB cable...So far it is still running....ill post back my results....fingers crossed, I hope this works!
I restarted the print...I waited for it to start and then pulled the USB cable...So far it is still running....ill post back my results....fingers crossed, I hope this works!
- Sun Jun 12, 2016 3:22 am
- Forum: Tech Support
- Topic: Print stops (incomplete) after 20+ hrs...need help
- Replies: 45
- Views: 38959
Re: Print stops (incomplete) after 20+ hrs...need help
I'll have to test that tomorrow...I just posted over to S3D's forum as well...
I hope you are correct Jules...that would at least determine if it is S3D or the printer itself having an issue...one piece of the puzzle!
I hope you are correct Jules...that would at least determine if it is S3D or the printer itself having an issue...one piece of the puzzle!