Need some assistance getting started...post here...
-
- v3A to V3B extruder upgrade
by Joost » Fri Apr 08, 2016 8:42 pm
- 5 Replies
- 1639 Views
- Last post by Joost
Mon Apr 11, 2016 1:52 am
-
- How To: Guide to Getting Started (with Troubleshooting Tips)
by Jules » Tue Sep 15, 2015 12:01 am
- 20 Replies
- 21454 Views
- Last post by jsc
Mon Mar 28, 2016 5:26 pm
-
- Looking for help creating a model for mini soccer cones
by classicvideogamer » Sun Mar 27, 2016 1:28 am
- 3 Replies
- 1744 Views
- Last post by classicvideogamer
Sun Mar 27, 2016 3:28 pm
-
- S3D virtual machine does not match M2 Bed
by Kirk.AIA » Tue Mar 22, 2016 2:51 am
- 19 Replies
- 5983 Views
- Last post by Hugs
Fri Mar 25, 2016 12:25 am
-
- Filament snapped in drive while loading
by no3dprintexperience » Tue Mar 22, 2016 11:35 pm
- 2 Replies
- 1089 Views
- Last post by jprochnow
Thu Mar 24, 2016 12:47 am
-
- Cancelling a print and other typical beginner questions
by ihadavision » Wed Mar 16, 2016 11:46 pm
- 5 Replies
- 1653 Views
- Last post by Hugs
Sat Mar 19, 2016 8:28 am
-
- So... what causes this
by Neep » Wed Mar 02, 2016 9:49 pm
- 12 Replies
- 4308 Views
- Last post by Tim
Fri Mar 18, 2016 1:43 pm
-
- Total beginner question about PLA
by no3dprintexperience » Mon Mar 14, 2016 2:15 am
- 4 Replies
- 1805 Views
- Last post by no3dprintexperience
Mon Mar 14, 2016 1:35 pm
-
- New to all this... Looking to network
by Jadedwarlord » Tue Feb 16, 2016 8:37 pm
- 12 Replies
- 3799 Views
- Last post by Jadedwarlord
Sun Mar 13, 2016 4:37 am
-
- Kapton 'Polyamide' Tape - What's the skinny?
by MakerMike7 » Wed Aug 27, 2014 3:41 am
- 13 Replies
- 5123 Views
- Last post by ajmadison
Thu Mar 10, 2016 10:36 pm
-
- Getting started video posted for Rev. E
by Hugs » Thu Mar 10, 2016 10:12 pm
- 1 Replies
- 3256 Views
- Last post by thunderbt3
Thu Mar 10, 2016 10:17 pm
-
- Z Offset "Theory"
by kkessler » Thu Feb 25, 2016 4:00 pm
- 11 Replies
- 2247 Views
- Last post by Jules
Fri Feb 26, 2016 8:12 pm
-
- Noob questions
by Cybergooch » Sat Feb 20, 2016 4:36 am
- 8 Replies
- 1651 Views
- Last post by willnewton
Thu Feb 25, 2016 10:57 pm
-
- Just ordered my M2
by BillCollins » Tue Feb 16, 2016 11:35 pm
- 4 Replies
- 826 Views
- Last post by BillCollins
Sat Feb 20, 2016 12:12 am
-
- Z depth calibration
by kyphur » Thu Feb 18, 2016 1:07 am
- 8 Replies
- 1175 Views
- Last post by Jules
Thu Feb 18, 2016 4:38 am
-
- MakerGear from Amazon - Warranty
by Spencer » Sun Feb 07, 2016 7:00 pm
- 1 Replies
- 693 Views
- Last post by Jules
Sun Feb 07, 2016 7:04 pm
-
- Printing from SD card.
by JeremyV » Wed Jan 20, 2016 5:02 pm
- 3 Replies
- 1045 Views
- Last post by Jules
Wed Jan 20, 2016 7:35 pm
-
- Problems connecting printer
by Isaaccalvillo » Fri Jan 15, 2016 8:07 am
- 1 Replies
- 576 Views
- Last post by claudconger
Tue Jan 19, 2016 11:47 am
-
- Before I buy, any suggestions
by cosi » Mon Sep 14, 2015 3:27 pm
- 4 Replies
- 1663 Views
- Last post by claudconger
Tue Jan 19, 2016 11:39 am
-
- Two new problems after 3 months of no printing
by akkrolnik » Sat Jan 09, 2016 9:34 pm
- 15 Replies
- 2874 Views
- Last post by jimc
Mon Jan 11, 2016 2:35 am
-
- Com Port , Setting Baud Rate
by ray » Sun Nov 29, 2015 10:02 pm
- 2 Replies
- 1077 Views
- Last post by ray
Mon Nov 30, 2015 4:02 am
-
- 3DBenchy Test Print – would welcome some feedback
by NickN » Fri Nov 20, 2015 5:24 pm
- 12 Replies
- 4039 Views
- Last post by PcS
Thu Nov 26, 2015 12:28 pm
-
- How do I measure my nossle?
by WarMace » Mon Nov 23, 2015 8:28 pm
- 6 Replies
- 1443 Views
- Last post by Jules
Wed Nov 25, 2015 1:55 pm
-
- Newbie Question
by tomdoyle1948 » Sat Nov 21, 2015 10:11 pm
- 2 Replies
- 827 Views
- Last post by jsc
Sun Nov 22, 2015 5:13 am
-
- Prints pulling up at corners
by naturalstate720 » Thu Nov 05, 2015 8:10 pm
- 106 Replies
- 16045 Views
- Last post by naturalstate720
Wed Nov 18, 2015 5:14 am
Return to Board index
Who is online
Users browsing this forum: No registered users and 4 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum