MIC6 preorder number 3 *back for sale*

The place to discuss your hardware and software/firmware modifications...
NavyDT
Posts: 33
Joined: Sun Dec 11, 2016 6:12 pm

Re: MIC6 preorder number 3

Post by NavyDT » Mon Dec 12, 2016 5:07 pm

I ordered it pre-cut to 7.95in by 9.95 inch, hopefully I will not have to screw with it after that :) if I do then I guess I could attempt to file it or try and find a machine shop...

daveb
Posts: 22
Joined: Tue Nov 03, 2015 4:06 am

Re: MIC6 preorder number 3

Post by daveb » Thu Dec 22, 2016 2:58 am

I'll take one

3dPrintingMD
Posts: 277
Joined: Fri Oct 02, 2015 5:37 am

Re: MIC6 preorder number 3

Post by 3dPrintingMD » Thu Dec 22, 2016 3:32 am

Angle Grinder will do the trick. Use tape on the "printing surface" to act as a guide line. The with the angle grinder and a sanding disk, slowly work the sides down to the tape lines.

Another member also did this, but they only worked on the area near the corners. When I did this, I did the entire length. Results are the same.
M2 - V4, MIC-6 Build Plate, Astrosyn Damper's(X/Y), Rev. E, Geeetech LCD

S3D - FFF Settings https://forum.simplify3d.com/viewtopic.php?f=8&t=2367
Print Quality Troubleshooting https://www.simplify3d.com/support/prin ... eshooting/

1oldclown
Posts: 6
Joined: Sat Aug 09, 2014 3:14 am

Re: MIC6 preorder number 3

Post by 1oldclown » Thu Dec 22, 2016 4:06 pm

I a man interested in (1) , please!

charmanter
Posts: 2
Joined: Mon Dec 26, 2016 1:52 pm

Re: MIC6 preorder number 3

Post by charmanter » Mon Dec 26, 2016 2:12 pm

I'm also interested in (1) too!

User avatar
insta
Posts: 2000
Joined: Tue Sep 16, 2014 3:59 am

Re: MIC6 preorder number 3

Post by insta » Tue Dec 27, 2016 9:36 pm

We're getting pretty close now ...
Custom 3D printing for you or your business -- quote [at] pingring.org

LonV
Posts: 44
Joined: Wed Apr 09, 2014 8:40 pm

Re: MIC6 preorder number 3

Post by LonV » Thu Dec 29, 2016 7:48 pm

I'm interested in 1.

User avatar
atomic_peach
Posts: 37
Joined: Sun Dec 04, 2016 2:14 am
Location: Philadelphia, PA

Re: MIC6 preorder number 3

Post by atomic_peach » Thu Dec 29, 2016 8:02 pm

I'm interested in 1.

spmahoney78
Posts: 27
Joined: Thu Mar 24, 2016 1:01 am

Re: MIC6 preorder number 3

Post by spmahoney78 » Wed Jan 04, 2017 2:32 am

I'm excited to get this ordered. I noticed some warp in my glass over the holidays.

vesteroid
Posts: 28
Joined: Tue Jan 03, 2017 4:45 am

Re: MIC6 preorder number 3

Post by vesteroid » Wed Jan 04, 2017 9:14 pm

I would like one please, let me know how to pay.

Post Reply