MakerGear Forum

Posted: **Fri Oct 31, 2014 6:01 am**

Ok, I have good news and bad news. It seems to be working great! The bad news is you can't use the original spool holder with the mount as I modified it, so if you want to use it you'd have to print both pieces. Also the nylon washers I used are optional I included to reduce wear from the parts rubbing against each other.

It was made per creative commons license based on this design: http://www.thingiverse.com/thing:119488

This is the link to the REMIX: http://www.thingiverse.com/thing:523415

: IMG_6851_1.jpg (97.93 KiB) Viewed 11391 times

: IMG_6876_1.jpg (156.28 KiB) Viewed 11391 times

: IMG_6877_1.jpg (176.93 KiB) Viewed 11391 times

: IMG_6878_1.jpg (165.91 KiB) Viewed 11391 times

Posted: **Mon Nov 03, 2014 2:35 pm**

I just got back from a short vacation. I will be printing this up this week.
Thanks for posting it.
Mark

Posted: **Wed Nov 05, 2014 6:44 pm**

Your remake is famous

http://pushplastic.com/collections/3-kg ... c3c2fbdf18

jdacal wrote:Ok, I have good news and bad news. It seems to be working great! The bad news is you can't use the original spool holder with the mount as I modified it, so if you want to use it you'd have to print both pieces. Also the nylon washers I used are optional I included to reduce wear from the parts rubbing against each other.

It was made per creative commons license based on this design: http://www.thingiverse.com/thing:119488

This is the link to the REMIX: http://www.thingiverse.com/thing:523415

IMG_6851_1.jpg

IMG_6876_1.jpg

IMG_6877_1.jpg

IMG_6878_1.jpg

Posted: **Wed Nov 05, 2014 7:03 pm**

LOL! Thanks Mark

Edit: Wow that's a pretty heavy reel, 6.6 lb. Might have to load test this thing.

Posted: **Sun Nov 09, 2014 3:01 am**

Hey Markb, if you haven't printed it yet, might want to hold off on it. I'm making a change to it so that it can take some spool adapters I'm re-mixing. I'm going to have to add a groove to it.

Posted: **Sun Nov 09, 2014 3:46 am**

I was going to print it tomorrow but I will hold off for the new changes.

Posted: **Sun Nov 09, 2014 3:47 am**

I'll probably post the updates tomorrow. I'm printing it now, just waiting to confirm everything fits together ok.

Posted: **Mon Nov 10, 2014 12:47 am**

Ok markb its ready. If you decide to print the spool adapters you'll need to wire brush the interior diameter a little so they go on tight but not too tight. I'd still put a clip on the spool holder just in case they loosen up after some use.

I'll add more adapters as I run into the various sizes. I have an idea for an attachment for the small taulman holes. Whenever I buy my first Taulman I'll make it.

http://www.thingiverse.com/thing:523415

: Includes spool holder mount, spool holder, spool holder 52mm adapters, and clips; M2 Spool Holder Kit Ver 1.2.jpg (132.69 KiB) Viewed 11291 times

: The 52mm Spool adapters can slide in the groove for different width reels.; 2014-11-09 18.11.37_1.jpg (172.24 KiB) Viewed 11291 times

: Show here with a narrower reel...; 2014-11-09 18.12.48_1.jpg (159.59 KiB) Viewed 11291 times

: ...and here with a wider reel; 2014-11-09 18.15.07_1.jpg (170.72 KiB) Viewed 11291 times

Posted: **Tue Mar 03, 2015 8:22 am**

I added this new adapter for the spool holder to Thingiverse today:

http://www.thingiverse.com/thing:706365

: This is an adapter for the Taulman3D Spools. Lets you use the spool without having to remove the large spool adapter.; Taulman Adapter.jpg (59.7 KiB) Viewed 11031 times

MakerGear Forum

Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.

Re: Printing with my new spool holder.