I caused a filament jam by cutting the filament and trying to extrude it through instead of retracting it. I didn't realize at the time that the gear would have no way to push it all the way into the extruder...I guess I should have reasoned that, but I can be a fool sometimes. Anyway, one of the nice guys at MakerGear explained how to fix it. I followed his instructions and filmed the whole thing just incase anybody else runs into this same predicament. Below is a link to the video. Enjoy!
https://youtu.be/yNi1q5U6Nus
P.S. As one of the other posters said: To avoid this problem, Don't cut the filament! Just heat the extruder and retract it.
How To Fix a Filament Jam, with Video
How To Fix a Filament Jam, with Video
Last edited by beerstar on Mon Jan 18, 2016 8:07 pm, edited 3 times in total.
Re: Filament Jam
Yep, that's how it's done all right. Nice vid! Should be helpful.
Re: Filament Jam
Thanks for the compliment, Jules. FYI ~ I've learned a lot from your posts, so thanks for that too!
Re: Filament Jam
Thanksa berry berry much!
(You know, if you wouldn't mind changing the title of your original post to something like "How To Fix a Filament Jam, with Video", then newcomers will be able to find it more easily down the road. Otherwise they tend to disappear over time. I was trying to get "How To" into the titles of useful posts that can help people resolve problems. Makes it easier to search. )
(You know, if you wouldn't mind changing the title of your original post to something like "How To Fix a Filament Jam, with Video", then newcomers will be able to find it more easily down the road. Otherwise they tend to disappear over time. I was trying to get "How To" into the titles of useful posts that can help people resolve problems. Makes it easier to search. )
-
- Posts: 277
- Joined: Fri Oct 02, 2015 5:37 am
Re: Filament Jam
I think you have it all figured out, but for anyone new here are a few pointers to avoid this.
Stop cutting filament off, its totally unnecessary, and resolves in jams. - To change filaments, heat up the hotend to the correct temp of the filament in the machine, then retract it out. No cutting involved.
When you do have a jam as shown in the video you could be saved by again heating the hot end, maybe go a bit hotter than usual. (Don't exceed the temp for that filament type). You might get lucky and will be able to push new/additional filament down through the top and it will force that piece out.
I have gotten to the point where I do not have jams from changing filaments. I print in PLA and PETG, and go back and forth between each of them.
Stop cutting filament off, its totally unnecessary, and resolves in jams. - To change filaments, heat up the hotend to the correct temp of the filament in the machine, then retract it out. No cutting involved.
When you do have a jam as shown in the video you could be saved by again heating the hot end, maybe go a bit hotter than usual. (Don't exceed the temp for that filament type). You might get lucky and will be able to push new/additional filament down through the top and it will force that piece out.
I have gotten to the point where I do not have jams from changing filaments. I print in PLA and PETG, and go back and forth between each of them.
M2 - V4, MIC-6 Build Plate, Astrosyn Damper's(X/Y), Rev. E, Geeetech LCD
S3D - FFF Settings https://forum.simplify3d.com/viewtopic.php?f=8&t=2367
Print Quality Troubleshooting https://www.simplify3d.com/support/prin ... eshooting/
S3D - FFF Settings https://forum.simplify3d.com/viewtopic.php?f=8&t=2367
Print Quality Troubleshooting https://www.simplify3d.com/support/prin ... eshooting/
Re: How To Fix a Filament Jam, with Video
If it's the same type of filament (just a different color) I cut it and just follow it in with the next color all the time and don't have any issues.
____________________________________________________
See my projects at https://www.theneverendingprojectslist.com
See my projects at https://www.theneverendingprojectslist.com
Re: How To Fix a Filament Jam, with Video
I sometimes do too, (especially when i'm color switching in the middle of a print), but you have to cut both the ends completely flat to do that successfully every time, (and push it in a little bit until the new strand catches) and i think the instructions that come with the machine advise you to cut an angle on the end you are feeding in. (And if you try to feed an angle cut strand in, with another strand in there, you're going to jam it for sure.)sthone wrote:If it's the same type of filament (just a different color) I cut it and just follow it in with the next color all the time and don't have any issues.
It's definitely more of a sure thing to just retract, (and you can check your bite marks while you're at it ), so for single color prints, that's what i do. Yeah, it wastes a little bit of filament, but it has probably saved a few prints from bad bite marks, so I figure it all washes out.
(I think for beginners, retraction is absolutely the best way to go. )