Oh For Heaven's Sake!

Ask the MakerGear community for assistance...
User avatar
Jules
Posts: 3144
Joined: Wed Jan 21, 2015 1:36 am

Re: Oh For Heaven's Sake!

Post by Jules » Fri Mar 20, 2015 2:13 am

Thought about putting in a full-house generator, we do get a lot of hurricanes around here.

Bought an M2 instead......... :lol:

lem
Posts: 162
Joined: Thu Jan 15, 2015 6:44 pm

Re: Oh For Heaven's Sake!

Post by lem » Thu Mar 26, 2015 4:02 am

I checked with the Simplify3D folks, here's what they had to say:
Thanks for contacting Simplify3D, I will be happy to help answer your question. In regards to the communication between Simplify3D Software and the printer, there is no checksum in our protocol, and we use the standard RepRap style communication. The software will make sure it receives and ok response from the printer to hopefully catch any errors in the communication should they arise, either from faulty usb cables, mismatch baud rate speed, etc., but there is no actual checksum or verification done on the communication stream.
The farther we come, the farther behind we get.

User avatar
insta
Posts: 2007
Joined: Tue Sep 16, 2014 3:59 am

Re: Oh For Heaven's Sake!

Post by insta » Thu Mar 26, 2015 4:07 am

Argh it's such a simple thing to add, too. It's literally built into the Marlin firmware already.
Custom 3D printing for you or your business -- quote [at] pingring.org

User avatar
jdacal
Posts: 466
Joined: Thu Jul 03, 2014 10:28 pm
Location: Florida
Contact:

Re: Oh For Heaven's Sake!

Post by jdacal » Thu Mar 26, 2015 7:38 pm

Wow no checksum! That's such a basic thing, I wonder what their reasoning is.

EDIT: Maybe that explains those rare times when I wake up and find the bed laying on the bottom in the middle of what appears to be a normal print job.
jdacal

live print feed: http://enctrading.com/printcam/
See me Crash and Burn in Real time!

Ronnien55
Posts: 60
Joined: Mon Dec 08, 2014 2:50 am
Location: Holly Springs NC

Re: Oh For Heaven's Sake!

Post by Ronnien55 » Sat Apr 04, 2015 7:00 pm

I had the same thing happen twice, i use usb to my MAC pro 2009 and Simply3D. I found that I had turned on my screen saver both times this happened. Whenever I am printing I turn screen saver off and it has not happened again. Not sure why that would cause an interrupt in USB communications.

lem
Posts: 162
Joined: Thu Jan 15, 2015 6:44 pm

Re: Oh For Heaven's Sake!

Post by lem » Sat Apr 04, 2015 7:53 pm

I wonder if there are enough S3D users here to get S3D to implement an option in S3D to use the checksum feature?

Larry

User avatar
ednisley
Posts: 1188
Joined: Fri Apr 11, 2014 5:34 pm
Location: Halfway up the Hudson
Contact:

Re: Oh For Heaven's Sake!

Post by ednisley » Sat Apr 04, 2015 9:19 pm

Ronnien55 wrote:turned on my screen saver both times this happened
Most likely, when Windows activates the screen saver it also triggers the power management functions: spin down the drives, slow the CPU, and turn off power to peripherals like, whoops, the USB ports.

The Arduino on the RAMBo board interprets that as a communications reset and pretty much stops whatever it was doing at the time. I don't know if you could recover based on command checksums, but at least you would know something awful had happened.
Last edited by ednisley on Sun Apr 05, 2015 12:51 pm, edited 1 time in total.

User avatar
Jules
Posts: 3144
Joined: Wed Jan 21, 2015 1:36 am

Re: Oh For Heaven's Sake!

Post by Jules » Sat Apr 04, 2015 10:03 pm

Well, I've learned my lesson.....any print over an hour goes onto the SD card. :D

User avatar
jdacal
Posts: 466
Joined: Thu Jul 03, 2014 10:28 pm
Location: Florida
Contact:

Re: Oh For Heaven's Sake!

Post by jdacal » Sun Apr 05, 2015 3:17 am

Jules wrote:Well, I've learned my lesson.....any print over an hour goes onto the SD card. :D
I've had the bed drop on me from SD cards too. I've had it happen with the Raspberry memory and on the SD with the same print at the same spot on the print. In those cases I go back and make some minor change on SD3 and regenerate the file. Its pretty rare though.
jdacal

live print feed: http://enctrading.com/printcam/
See me Crash and Burn in Real time!

User avatar
Jules
Posts: 3144
Joined: Wed Jan 21, 2015 1:36 am

Re: Oh For Heaven's Sake!

Post by Jules » Sun Apr 05, 2015 3:56 am

Great! :roll:

Post Reply