print suddenly stopped due to a gcode/firmware issue?
Posted: Thu Jun 05, 2014 5:26 am
I was in the middle of printing something and the print suddenly stopped for no apparent reason. I use a Raspberry Pi running Octoprint to control the printer, but it's not obvious whether it's the gcode, Octoprint, or firmware to blame. Here's the log, any ideas?
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Send: M105
Recv: ok
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: ok
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: Error:No Checksum with line number, Last Line:6428
Recv: Resend:6429
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Recv: Error:Line Number is not Last Line Number+1, Last Line:6428
Recv: Resend:6429
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Recv: ok
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: Error:Line Number is not Last Line Number+1, Last Line:6429
Recv: Resend:6430
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: ok
Recv: ok
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: Error:Line Number is not Last Line Number+1, Last Line:6430
Recv: Resend:6431
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: ok
Recv: ok
Send: M105
Recv: Error:Line Number is not Last Line Number+1, Last Line:6431
Recv: Resend:6432
Changing monitoring state from 'Printing' to 'Error: Printer requested li...'
Recv: ok
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Send: M105
Recv: ok
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: ok
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: Error:No Checksum with line number, Last Line:6428
Recv: Resend:6429
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Recv: Error:Line Number is not Last Line Number+1, Last Line:6428
Recv: Resend:6429
Send: N6429 G1 X41.025 Y245.824 E3.5575*85
Recv: ok
Recv: ok
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: Error:Line Number is not Last Line Number+1, Last Line:6429
Recv: Resend:6430
Send: N6430 G1 X41.857 Y246.406 E3.6066*91
Recv: ok
Recv: ok
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: Error:Line Number is not Last Line Number+1, Last Line:6430
Recv: Resend:6431
Send: N6431 G1 X53.331 Y234.932 E4.3909*95
Recv: ok
Recv: ok
Send: M105
Recv: Error:Line Number is not Last Line Number+1, Last Line:6431
Recv: Resend:6432
Changing monitoring state from 'Printing' to 'Error: Printer requested li...'
Recv: ok