Securing your bed: Binder clips, none, or other?
Re: Securing your bed: Binder clips, none, or other?
no hard feeling at all. i have never used pei so if that warps a bit then i can see that. i have glass on one printer and aluminum on the other 2. with that stuff there is no warp so everything just sits there inside the corners with nothing needed to hold anything down. just pick up the build plate, remove part and set the plate back down.
Re: Securing your bed: Binder clips, none, or other?
That upload was a result of my request as I made some custom components that work with the drive they sent with my V4 (which we discovered was actually was the dual left drive after he uploaded that one).creativedex wrote:Also anyone know what the latest revision to the filament drive was for? it was just posted 2 weeks ago
Another bed hold down solution... I kept them simple and printed out of PETG. One can swivel open for quick bed removal.
Last edited by kartcrg on Sun Jan 24, 2016 7:27 am, edited 2 times in total.
Re: Securing your bed: Binder clips, none, or other?
That's a good idea.
(Hey, everybody up Northeast.....don't go out partying this weekend.)
(Hey, everybody up Northeast.....don't go out partying this weekend.)
-
- Posts: 28
- Joined: Thu Oct 15, 2015 8:32 am
Re: Securing your bed: Binder clips, none, or other?
Since most of my prints are small the larger binder clips havent been a problem, when they are i just put them where they wont be in the way. But even just my bed corners without the binder clips its pretty well indexed in so i can print without them (with the glass), but the 1/4in pei requires the clips unless your printing on a 4in square in the middle of the bed
The one issues im sure most people will have with my corner design is that i had to chip the corners off the glass!... which was easy to do with tile snips and sanding the corners.
Did anyone else notice makergear sending out their glass with sanded edges now!? finally a nice finishing touch
The green (abs) ones were one of my very first designs, but turned out decently. thickened up the black (petg) this time around because the abs did warp a bit with 110 degree bed temps. However ive been using them for over a year still without adjustment.
sorry for the blurry pix they both were printing... thin walls too, actually surprised i got shots as good as i did!
The one issues im sure most people will have with my corner design is that i had to chip the corners off the glass!... which was easy to do with tile snips and sanding the corners.
Did anyone else notice makergear sending out their glass with sanded edges now!? finally a nice finishing touch
The green (abs) ones were one of my very first designs, but turned out decently. thickened up the black (petg) this time around because the abs did warp a bit with 110 degree bed temps. However ive been using them for over a year still without adjustment.
sorry for the blurry pix they both were printing... thin walls too, actually surprised i got shots as good as i did!
Re: Securing your bed: Binder clips, none, or other?
I secure my PEI/GLASS/HEATER combo together with larger binder clips but its getting to the point now where I need something lower profile and less intrusive because they stick up just enough that my cooling duct hits them for the first few layers and I have to have at least 6 binder clips to hold the PEI down well. I keep trying to think of a design that is flush on the top and doesnt encroach on the print area too much. I was thinking maybe a trim frame that covers a few mm of the border the whole way around out of spring steel or something but I havent decided on a good way to clip that down...
-
- Posts: 28
- Joined: Thu Oct 15, 2015 8:32 am
Re: Securing your bed: Binder clips, none, or other?
Farr0wn3d wrote:I secure my PEI/GLASS/HEATER combo together with larger binder clips but its getting to the point now where I need something lower profile and less intrusive because they stick up just enough that my cooling duct hits them for the first few layers and I have to have at least 6 binder clips to hold the PEI down well. I keep trying to think of a design that is flush on the top and doesnt encroach on the print area too much. I was thinking maybe a trim frame that covers a few mm of the border the whole way around out of spring steel or something but I havent decided on a good way to clip that down...
see my previous post with the thingivers link... let me know if you find a US seller too
Re: Securing your bed: Binder clips, none, or other?
Its seems that thingiverse is down at the moment
Re: Securing your bed: Binder clips, none, or other?
those clips are perfect creativedex, however I'm not sure where I would get the metal component?
-
- Posts: 28
- Joined: Thu Oct 15, 2015 8:32 am
Re: Securing your bed: Binder clips, none, or other?
Farr0wn3d wrote:those clips are perfect creativedex, however I'm not sure where I would get the metal component?
lol i asked the guy in the comments on the link but from what ive noticed they arent for sale here in the US or i just dont know what the correct term to search for them is... but they are sold at electrical supply stores in the UK
Re: Securing your bed: Binder clips, none, or other?
well then... Thanks for showing me how great it COULD be...