For instance, my "TPU" filament can change the print speed vs. "PETG" vs. "PLA". The temps change, the rafts change, etc. (yes, I occasionally still use rafts, there's reasons, shush)
Open the files up in Notepad++ or SublimeText 3 (or some other competent, free, XML editor). Look at this example for TPU:
Code: Select all
<autoConfigureMaterial name="TPU">
<filamentPricePerKg>15</filamentPricePerKg>
<filamentDensity>1.20</filamentDensity>
<useRaft>0</useRaft>
<defaultSpeed>1200</defaultSpeed>
<extruder name="Primary Extruder">
<extrusionMultiplier>1.33</extrusionMultiplier>
<retractionSpeed>1500</retractionSpeed>
<retractionDistance>.6</retractionDistance>
</extruder>
<temperatureController name="Primary Extruder">
<setpoint layer="1" temperature="200"/>
</temperatureController>
<temperatureController name="Heated Build Platform">
<setpoint layer="1" temperature="40"/>
</temperatureController>
<fanSpeed>
<setpoint layer="1" speed="0"/>
</fanSpeed>
</autoConfigureMaterial>
Code: Select all
<extruder name="Primary Extruder">
<toolheadNumber>0</toolheadNumber>
<diameter>0.75</diameter>
<autoWidth>0</autoWidth>
<width>0.9</width>
<useRetract>1</useRetract>
<retractionDistance>1</retractionDistance>
<extraRestartDistance>-0.3</extraRestartDistance>
<retractionZLift>0.5</retractionZLift>
<retractionSpeed>4500</retractionSpeed>
<useCoasting>1</useCoasting>
<coastingDistance>0.3</coastingDistance>
<useWipe>0</useWipe>
<wipeDistance>5</wipeDistance>
</extruder>
Code: Select all
<autoConfigureQuality name="0.20mm layer">
<layerHeight>0.2</layerHeight>
<topSolidLayers>4</topSolidLayers> *********
<bottomSolidLayers>4</bottomSolidLayers>
<skirtLayers>2</skirtLayers>
<infillPercentage>30</infillPercentage>
<supportInfillPercentage>40</supportInfillPercentage>
<firstLayerHeightPercentage>100</firstLayerHeightPercentage>
<firstLayerWidthPercentage>105</firstLayerWidthPercentage>
<firstLayerUnderspeed>0.3</firstLayerUnderspeed>
<supportExtraInflation>0.2</supportExtraInflation>
<denseSupportLayers>2</denseSupportLayers>
<denseSupportInfillPercentage>70</denseSupportInfillPercentage>
<supportHorizontalPartOffset>0.5</supportHorizontalPartOffset>
<supportUpperSeparationLayers>2</supportUpperSeparationLayers>
<supportLowerSeparationLayers>1</supportLowerSeparationLayers>
</autoConfigureQuality>
<autoConfigureQuality name="0.10mm layer">
<layerHeight>0.1</layerHeight>
<topSolidLayers>6</topSolidLayers> ************
<bottomSolidLayers>4</bottomSolidLayers>
<skirtLayers>2</skirtLayers>
<infillPercentage>30</infillPercentage>
<supportInfillPercentage>40</supportInfillPercentage>
<firstLayerHeightPercentage>150</firstLayerHeightPercentage>
<firstLayerWidthPercentage>125</firstLayerWidthPercentage>
<firstLayerUnderspeed>0.3</firstLayerUnderspeed>
<supportExtraInflation>0.2</supportExtraInflation>
<denseSupportLayers>3</denseSupportLayers>
<denseSupportInfillPercentage>70</denseSupportInfillPercentage>
<supportHorizontalPartOffset>0.5</supportHorizontalPartOffset>
<supportUpperSeparationLayers>2</supportUpperSeparationLayers>
<supportLowerSeparationLayers>1</supportLowerSeparationLayers>
</autoConfigureQuality>