Search found 1997 matches

by insta
Fri Jan 22, 2021 2:39 am
Forum: Pre-owned Gear
Topic: Testing waters to sell some of my production machines
Replies: 4
Views: 3542

Re: Testing waters to sell some of my production machines

... they are TMC2130 drivers, apparently. Its possible I got a "pre-production" run of them.

Anyway, it mostly just drops in. The Viki1 is a lot harder to hook up, so I didn't :lol:
by insta
Fri Sep 18, 2020 2:35 am
Forum: General Discussion
Topic: Questions from a new owner (of old M2)
Replies: 3
Views: 2373

Re: Questions from a new owner (of old M2)

Buy NEMA17 dampers. I have 6 M2's that until last week were in active production duty, some as old as 2012 (!!). Between all of them, they have run about 40 miles of filament. I have abused them, neglected them (*), covered them in hairspray overspray, broken the glass beds, shorted out the wiring i...
by insta
Wed Sep 16, 2020 2:31 am
Forum: Pre-owned Gear
Topic: Testing waters to sell some of my production machines
Replies: 4
Views: 3542

Re: Testing waters to sell some of my production machines

Last call, these babies are getting boxed up this week for eBay.
by insta
Mon Sep 07, 2020 9:20 pm
Forum: Tech Support
Topic: connect leftover filaments
Replies: 7
Views: 2747

Re: connect leftover filaments

If your current firmware does not understand or support M600, then you will have to flash updated firmware. There isn't a workaround for that (unless you want to do something silly like connect a loud buzzer to the runout sensor as an alarm)
by insta
Mon Sep 07, 2020 4:41 pm
Forum: Tech Support
Topic: connect leftover filaments
Replies: 7
Views: 2747

Re: connect leftover filaments

You can use a filament runout sensor. These use a leaf switch held closed by the presence of filament. When the filament runs out, the switch opens up and the printer firmware will enter a special mode to allow you to replace it. You usually end up with about 30cm of wasted filament, which is a far ...
by insta
Mon Sep 07, 2020 3:31 pm
Forum: Pre-owned Gear
Topic: Testing waters to sell some of my production machines
Replies: 4
Views: 3542

Testing waters to sell some of my production machines

I've got 6 of these workhorses that have served me well for years, but my printing seems to be moving in the industrial material space (ULTEM & up) and shrinking, so 6 is too many. I'm not in a huge hurry to let any of these babies go, but just seeing if anybody is interested in them. I have 5x 1.75...
by insta
Mon Sep 07, 2020 3:14 pm
Forum: Getting Started
Topic: contract someone to set up remotely my MakerGear M2
Replies: 4
Views: 2540

Re: contract someone to set up remotely my MakerGear M2

I'll jump on this and see whatcha need. Feel free to email or Hangouts me at bryan.boettcher at Google's mail service. I've also put together this video years ago for another person who wanted pretty much the same thing you're asking for, the "wat do? printing 101" question: https://www.youtube.com/...
by insta
Thu Dec 06, 2018 2:50 am
Forum: Modifications
Topic: Pre-Rev. E HBP Wire Bracket Upgrade
Replies: 2
Views: 3126

Re: Pre-Rev. E HBP Wire Bracket Upgrade

I stuck a Keenovo 250W/24v heater directly to the underside of a MIC6 plate, and I'm using your bracket to strain-relief the corregated tubing. Hopefully it goes well :)
by insta
Thu Dec 06, 2018 2:37 am
Forum: Modifications
Topic: Mic 6 tooling plate
Replies: 212
Views: 102252

Re: Mic 6 tooling plate

I found a handful of 7.75 x 10" MIC6 plates, about 4 left. mic6 [at] pingring.org if you want one.