Search found 308 matches

by Farr0wn3d
Sat Nov 27, 2021 5:10 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Yeah that was a tricky one, as I dont think there is a way of extracting that info from the machine as-is. But rather, if download your factory firmware from the Wiki, you can go through the files and find that setting. I believe its 0.8A, which was the default in the configurator tool anyway. It’s ...
by Farr0wn3d
Thu Nov 25, 2021 8:14 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Thanks man, I appreciate the well wishes. You could be right about the connectors being compatible. I changed them all just for the sake of uniformity and I knew my RAMBo was toast anyway so I wasn’t worried about reverting back, as it is unlikely, and shouldn’t be too hard to redo the connections i...
by Farr0wn3d
Thu Nov 25, 2021 6:30 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Airscapes, I just realized that I missed one of your question posts before. I do not have a BL touch sensor. I mechanically level my bed using a dial indicator and recording the measurements in a grid pattern and then I strategically apply layers of kapton tape to the underside of the buildtak flexp...
by Farr0wn3d
Sun Nov 21, 2021 5:28 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

The fan outputs are typically the voltage supplied by your PSU for everything else, OR you can jumper them to be powered by 5v that the board converts.
by Farr0wn3d
Thu Nov 18, 2021 4:26 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

This is where I bought it from: https://spool3d.ca/duet-2-wifi-3d-printer-control-board/ I got the board with the integrated antenna, but I would do the external antenna if I bought it again. The signal isnt super strong and I'm not that far from the router. I've had my crimpers since I bought the M...
by Farr0wn3d
Tue Nov 16, 2021 5:14 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Perfect! a couple weeks will be far more than enough. If I were to have sat down and did it all start to finish I could have banged it out in a weekend.
by Farr0wn3d
Tue Nov 16, 2021 3:50 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

I'll try to get as much info as I can here. Just an FYI since this is a large part of what is driving your decision, I printed a fan guard last night in PETG with a 0.25mm nozzle and I made the screw holes 3.5mm in fusion, and in real life they were 3.25mm. I attribute this disparity to thermal shri...
by Farr0wn3d
Mon Nov 15, 2021 1:18 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 20
Views: 278

Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Hey everyone, after I blew the Z stepper driver on my printer's original Rambo board, I decided to upgrade to a Duet 2 wifi. I just wanted to make this post now that the printer is back up and running and say how pleased I am with the upgrade, and to recommend for anyone to do the same if they are i...
by Farr0wn3d
Sun Oct 31, 2021 10:45 pm
Forum: Tech Support
Topic: Z motor or its driver damaged?
Replies: 1
Views: 153

Re: Z motor or its driver damaged?

Update: The X and Y axes both behave normally, so I swapped the Z for the Y and now Z moves as it should when I use the Y controls, and Y just shakes and sounds like crap. It appears that I have damaged the board. Definitely not thrilled about having to replace the whole board because 1 stepper driv...
by Farr0wn3d
Sun Oct 31, 2021 7:48 pm
Forum: Tech Support
Topic: Z motor or its driver damaged?
Replies: 1
Views: 153

Z motor or its driver damaged?

Hey everyone, I just started using Octoprint and had to kill a print before it was done, but I'm not familiar with the controls of octo yet, so I cancelled the print and wanted to move the nozzle away from the print while it was still hot so I just turned the knob on the top of the lead screw to low...