Search found 311 matches

by Farr0wn3d
Tue Nov 30, 2021 10:09 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

The Z steps that are in the config that I posted to the Duet forum will be the ones that I’m using. I didn’t mess with them at all while I was getting it all up and running. I arrived on the new value by using a digital dial indicator to verify that the bed was travelling what I was instructing it t...
by Farr0wn3d
Tue Nov 30, 2021 6:49 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Hey Where did you get this value for steps per mm on Z in your config (from duet forum post) and are you using this value or did it get changed. It does not match the supposid value in the old Marlin config found on the old makergear m2 firmware site which I have listed below Your config M92 X88.89...
by Farr0wn3d
Tue Nov 30, 2021 6:43 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Airscapes, the Z axis will be another difference between our setups as I’m running an e3d titan, v6 nozzle, and a customer carriage mount for the motor. I have lost some Z axis travel as a result. I have my Z max for the printer set to the stock 200, but I fine tune the actual offset to somewhere ar...
by Farr0wn3d
Sat Nov 27, 2021 5:10 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Yeah that was a tricky one, as I dont think there is a way of extracting that info from the machine as-is. But rather, if download your factory firmware from the Wiki, you can go through the files and find that setting. I believe its 0.8A, which was the default in the configurator tool anyway. It’s ...
by Farr0wn3d
Thu Nov 25, 2021 8:14 pm
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Thanks man, I appreciate the well wishes. You could be right about the connectors being compatible. I changed them all just for the sake of uniformity and I knew my RAMBo was toast anyway so I wasn’t worried about reverting back, as it is unlikely, and shouldn’t be too hard to redo the connections i...
by Farr0wn3d
Thu Nov 25, 2021 6:30 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Airscapes, I just realized that I missed one of your question posts before. I do not have a BL touch sensor. I mechanically level my bed using a dial indicator and recording the measurements in a grid pattern and then I strategically apply layers of kapton tape to the underside of the buildtak flexp...
by Farr0wn3d
Sun Nov 21, 2021 5:28 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

The fan outputs are typically the voltage supplied by your PSU for everything else, OR you can jumper them to be powered by 5v that the board converts.
by Farr0wn3d
Thu Nov 18, 2021 4:26 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

This is where I bought it from: https://spool3d.ca/duet-2-wifi-3d-printer-control-board/ I got the board with the integrated antenna, but I would do the external antenna if I bought it again. The signal isnt super strong and I'm not that far from the router. I've had my crimpers since I bought the M...
by Farr0wn3d
Tue Nov 16, 2021 5:14 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

Perfect! a couple weeks will be far more than enough. If I were to have sat down and did it all start to finish I could have banged it out in a weekend.
by Farr0wn3d
Tue Nov 16, 2021 3:50 am
Forum: Modifications
Topic: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E
Replies: 26
Views: 389

Re: Retrofitting a Duet 2 wifi into Makergear M2 Rev. E

I'll try to get as much info as I can here. Just an FYI since this is a large part of what is driving your decision, I printed a fan guard last night in PETG with a 0.25mm nozzle and I made the screw holes 3.5mm in fusion, and in real life they were 3.25mm. I attribute this disparity to thermal shri...