Search found 15 matches

by fmeroney
Wed Nov 17, 2021 4:43 am
Forum: Software
Topic: Klipper
Replies: 6
Views: 7709

Re: Klipper

Did you update your config files? I'm trying to get some settings close but they dont seem to match up now. Im sure Klipper has changed the format... Thx! I know this is an old post, but in case anyone is interested, I created a basic configuration and was able to print with it etc. I have submitted...
by fmeroney
Tue Aug 10, 2021 2:26 am
Forum: Tech Support
Topic: Power issues
Replies: 1
Views: 801

Re: Power issues

Ok I decided to try a couple scenarios. I tried printing w/out bed heat and ran into the same issue where the PS shuts down. This leads me to believe my RAMBo is fried. When power is switched to either the Ext or Heated Bed the PS shuts down. I would assume there is a short somewhere... any ideas on...
by fmeroney
Tue Aug 10, 2021 1:27 am
Forum: Tech Support
Topic: Power issues
Replies: 1
Views: 801

Power issues

I have an older M2 w/dual Extruders… circa 2010ish. I woke after an overnight print to find that the print failed and machine stopped with what seemed to be strange noises coming from the M2. After investigation the power was at 14v, and the power supply was acting strange when cycled… abnormal clic...
by fmeroney
Sun Sep 27, 2015 7:57 pm
Forum: M2 Dual Extruder
Topic: Makergear M2 Dual with LCD - Experimental FW
Replies: 5
Views: 6323

Re: Makergear M2 Dual with LCD - Experimental FW

Do you have the sketch available? I would rather upload via arduino and be able to tweak it for the extras on my machine. Thanks! Hi I am attaching my final version as it seems to have resolved all the issues I didnt like such as: 1) Simplify3d connection issues 2) Jerking 3) Axis drifting 4) Abilit...
by fmeroney
Sun Sep 27, 2015 3:55 pm
Forum: M2 Dual Extruder
Topic: Dual Extruder Firmware with VIKI LCD Panel
Replies: 24
Views: 23479

Re: Dual Extruder Firmware with VIKI LCD Panel

@Don Yeah i mixed up the extruder fan & bed fan on re-install.... STUPID! @fmeroney: Not sure about the fans... Try pushing the reset button and see what happens? Perhaps, reinstall the firmware after pushing the reset button? I doubt it's the wiring... As far as the jerk rates and accel, I've never...
by fmeroney
Sun Sep 27, 2015 3:53 pm
Forum: M2 Dual Extruder
Topic: Dual Extruder Firmware with VIKI LCD Panel
Replies: 24
Views: 23479

Re: Dual Extruder Firmware with VIKI LCD Panel

FYI, this was due to operator error. Need to make sure the plugs are correct before you post about how things are not working... sorry all. Works great but my extrude and case fan are not turning on... Any ideas? Works when i have the stock dual firmware. Also, do the jerk rates seem high? It's fixe...
by fmeroney
Thu May 21, 2015 11:03 pm
Forum: M2 Dual Extruder
Topic: Dual Extruder Firmware with VIKI LCD Panel
Replies: 24
Views: 23479

Re: Dual Extruder Firmware with VIKI LCD Panel

Works great but my extrude and case fan are not turning on... Any ideas? Works when i have the stock dual firmware. Also, do the jerk rates seem high? It's fixed! Thanks to insta and jsc! I modified the firmware and now the extruders are both valid and heat as they should. I am using Simplify3D with...
by fmeroney
Thu May 21, 2015 10:57 pm
Forum: M2 Dual Extruder
Topic: Dual Ext & Simplify GCODe questions
Replies: 5
Views: 6380

Re: Dual Ext & Simplify GCODe questions

I did, what I'm doing is adding a silicone rubber wiper near the stepper on the right side so a quick jog to 215 will wipe an then return... actually getting some progress. thanks for the tip!! Did you build a wiper? How does it work? If you are in absolute mode (G90), all coordinates should be abso...
by fmeroney
Sun May 17, 2015 6:09 pm
Forum: M2 Dual Extruder
Topic: Dual Ext & Simplify GCODe questions
Replies: 5
Views: 6380

Re: Dual Ext & Simplify GCODe questions

Make sure T0 is selected when you start. Here is my startup gcode for dual. I just replicate the usual dance to do the purge in two parts. Some subtleties: Do T1 first, then T0 (assuming you're going to start printing with T0). This leaves T1 primed and drooling all over the place for the first lay...
by fmeroney
Thu May 14, 2015 4:56 am
Forum: M2 Dual Extruder
Topic: Dual Ext & Simplify GCODe questions
Replies: 5
Views: 6380

Dual Ext & Simplify GCODe questions

Hi All, Having some Gcode issues. What I'm trying to do is purge both extruders on my MakerGear M2... however before I keep wasting PLA, let me ask you guys/girls what I'm doing wrong. Starting script::: M108 S255 ; turn on M2 fans G28 ; home all axes G1 Y50 Z0.3 F9600 ; move forward to avoid binder...