Search found 385 matches
- Wed Jan 20, 2016 6:22 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 240780
Re: Testers Needed
Sent.
- Wed Jan 20, 2016 3:56 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 240780
Re: Testers Needed
I just discovered a big oops with the new design. The corner clip closest to bed position X=0, Y=max is colliding with the nut on the underside of the X gantry. I think the easiest fix is to remove that X gantry screw and nut, since it's not the end one I don't think it'll make any difference. I too...
- Wed Jan 20, 2016 3:35 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 240780
Re: Testers Needed
After my previous observation that the nozzle was almost touching the bed and dragging oozing plastic across the bed I changed my startup script in S3D from: M204 T10000 ; increase default retraction acceleration M201 X1200 Y800 Z500 ; reduce maximum acceleration to reduce ringing G28 ; home all axe...
- Wed Jan 20, 2016 1:29 am
- Forum: Printed Object Showcase
- Topic: Talented maker creates multi-colored '3D printed aviary' usi
- Replies: 14
- Views: 18634
Talented maker creates multi-colored '3D printed aviary' usi
Anyone catch this article http://www.3ders.org/articles/20160120- ... ify3d.html - she uses a M2.
- Fri Jan 15, 2016 2:41 am
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 240780
Re: Testers Needed
Is the new test code available yet? I need to relevel the bed and set Z anyway.
- Mon Jan 11, 2016 2:22 am
- Forum: Modifications
- Topic: PEI Bed Surface
- Replies: 161
- Views: 187771
Re: PEI Bed Surface
If PLA did stick to cold PEI then it wouldn't release from the bed very well. Kazolar (who I work with in our day jobs) said I didn't get a good lamination between the PEI and the glass so it'll have to be redone. I was surprised at this PLA print warping becuase I didn't think PLA was supposed to W...
- Mon Jan 11, 2016 12:51 am
- Forum: Modifications
- Topic: PEI Bed Surface
- Replies: 161
- Views: 187771
Re: PEI Bed Surface
The bed was heated to 60C
- Sun Jan 10, 2016 6:58 pm
- Forum: Modifications
- Topic: Testers Needed
- Replies: 246
- Views: 240780
Re: Testers Needed
I did a bunch of prints with the Z Max setup yesterday and noticed a potential issue. After the bed confirms the stop and starts to rise it does a nice Y shift to avoid hitting the clip, but then the nozzle comes close to the bed a bit higher up before moving off to the right for the purge. The prob...
- Sun Jan 10, 2016 5:37 am
- Forum: Modifications
- Topic: PEI Bed Surface
- Replies: 161
- Views: 187771
Re: PEI Bed Surface
Installed PEI on my bed New Years Eve (I'm a party animal), just tried printing a pen case tonight out of PLA and the PLA stuck so strongly to the PEI and warped that it delaminated the PEI from the glass on both sides. Argh.
- Sun Jan 10, 2016 5:35 am
- Forum: Modifications
- Topic: PEI Bed Surface
- Replies: 161
- Views: 187771
Re: PEI Bed Surface
Thanks insta