Search found 226 matches: abs temperature
Searched query: abs temperature
- Sun Nov 26, 2023 2:38 pm
- Forum: Tech Support
- Topic: Extruder motor stops responding/moving
- Replies: 12
- Views: 76310
Re: Extruder motor stops responding/moving
... flex plates for all 3. So far the PIE is working really well with ABS and everything else. I do use the nylon plate for nylon. I don't run ... on the other Makergear machines that have them. I run one for each bed temperature I use, utilizing the max number of points the software supports. ...
- Thu Nov 04, 2021 3:57 am
- Forum: General Discussion
- Topic: Feed Issues
- Replies: 6
- Views: 23208
- Thu Jan 28, 2021 6:23 pm
- Forum: M3-ID
- Topic: First Layer Cal with PETG
- Replies: 5
- Views: 20108
First Layer Cal with PETG
I'm trying to do a first layer calibration using PETG and a PEI sheet. I selected the ABS temp range, as that seemed to be the closest available setting. Is there any way to do a first layer cal with custom temperature settings?
TIA,
Frank
TIA,
Frank
- Tue May 26, 2020 5:35 pm
- Forum: General Discussion
- Topic: Ultra One Bed Leveling Procedure
- Replies: 10
- Views: 39099
Ultra One Bed Leveling Procedure
... MakerGear provides 2 options for plastic, and no way to adjust the temperature. We have a problem with this because we don't want to swap in PLA every time we want to adjust the z-height. Also, the ABS option sets the hotend to 265 C, which is wayyy to hot for our ABS, which ...
- Sat Oct 05, 2019 10:58 pm
- Forum: Tech Support
- Topic: How to Switch from PETG to to PLA without a clog?
- Replies: 5
- Views: 11194
Re: How to Switch from PETG to to PLA without a clog?
... type you run about 8-10" of this through your hot end a the same temperature as the previous filament. You need to do it slowly so it blends ... stuff. If done with every change you will never get a clog. I print ABS /PLA /PETG /Nylone/ TPU never do I remove the nozzle or have a clog. ...
- Sun Jul 07, 2019 11:19 pm
- Forum: Modifications
- Topic: Thermostat to control heater
- Replies: 0
- Views: 12163
Thermostat to control heater
I have been printing a lot of ABS lately, I really like the ABS Makergear sells, they say it someone local would ... them that MG does not carry. Anyway, I had added a very small heater (remove the temperature cut off switch on it as it did not work right) and end up leaving it on ...
- Mon Apr 01, 2019 8:06 pm
- Forum: Printed Object Showcase
- Topic: M3 ID REV 0 Enclosure made with printed hardware
- Replies: 5
- Views: 20113
Re: M3 ID REV 0 Enclosure made with printed hardware
It's pretty nice Dave,
Does your heater have a thermostat? You mentioned a thermometer? What temperature have you found to be best for printing ABS?
best,
john
Does your heater have a thermostat? You mentioned a thermometer? What temperature have you found to be best for printing ABS?
best,
john
- Thu Feb 21, 2019 8:04 pm
- Forum: Tech Support
- Topic: Multiple Super Weird Failure Modes
- Replies: 3
- Views: 5796
Multiple Super Weird Failure Modes
... is a single extruder V4 24 volt M2 that's run several hundred kg of ABS and PLA through four different nozzles on two different hot ends. It's ... no electrical or code mods. Just wouldn't extrude. I noticed that the temperature of the hot end was drifting down. I'm using S3D, so I manually ...
- Sat Sep 22, 2018 10:20 pm
- Forum: Tech Support
- Topic: Best bed and quality spool for ABS?
- Replies: 7
- Views: 9786
Re: Best bed and quality spool for ABS?
I dont know it may be a thermal issue. I do have my M2 in an sealed enclosure with heat lamps and a temperature controller. Right now I have it set to 135F in the enclosure.
- Wed Aug 08, 2018 1:27 am
- Forum: Modifications
- Topic: nema17 dampers
- Replies: 160
- Views: 296826
Re: nema17 dampers
I sent a mail to support to get the operating temperature range of the steppers. I have been printing for a few hours with pla ... around 120F, room temp is about is 82F. With the enclosure closed printing abs I crack the top when the temp hit 103F but never measured the motor temp. I ...